Behringer EUROPOWER EP1500 User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Version 1.4 June 2005

Users Manual

EUROPOWER

EP1

500/EP2500

EUROPOWER EP1500/EP2500

This symbol, wherever it appears, alerts you to the

presence of uninsulated dangerous voltage inside

the enclosurevoltage that may be sufficient to

constitute a risk of shock.

This symbol, wherever it appears, alerts you to

important operating and maintenance instructions

in the accompanying literature. Please read the

manual.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:

To reduce the risk of electric shock, do not remove

the top cover (or the rear section). No user

serviceable parts inside; refer servicing to qualified

personnel.

WARNING:

To reduce the risk of fire or electric shock, do not

expose this appliance to rain and moisture. The

apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such

as vases, shall be placed on the apparatus.

DETAILED SAFETY INSTRUCTIONS:

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in

accordance with the manufacturers instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving

the cart/apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been

dropped.

15) CAUTION - These service instructions are for use by

qualified service personnel only. To reduce the risk of

electric shock do not perform any servicing other than

that contained in the operation instructions unless you

are qualified to do so.

EUROPOWER EP1500/EP2500

EP1500/EP2500

EUROPOWER

High-end power amp with optional bridge mono operation mode for live applications

2 x 700 Watts (EP2500: 2 x 1200 Watts) into 2 Ohms, 1400 Watts (EP2500: 2400 Watts) into 4 Ohms

bridged operation

2-channel, parallel or bridged mono operating modes for flexible application

Independent limiters for each channel offer dependable protection against distortion

Precise signal and clip LED indicators to monitor performance

Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies

Professional Speakon

-compatible and touch-proof binding post loudspeaker outputs enable secure

operation*

Balanced XLR and 1/4" TRS inputs

Connection option for extra amps in parallel operation

Ultra-reliable Toshiba

/Fairchild

high-power transistors*

High-quality components and exceptionally rugged construction for long life and durability

High-current Toroid

toroidal transformer for absolute reliability and lowest noise emission*

Back-to-front ventilation system including air filter with automatically adjusting fan speed for smooth

operation

Independent DC and thermal overload protection on each channel automatically protects amplifier and

speakers

Conceived and designed by BEHRINGER Germany

* All Trademarks mentioned belong to their respective owners and are not affiliated with BEHRINGER

EUROPOWER EP1500/EP2500

TABLE OF CONTENTS

1. INTRODUCTION ......................................................... 4

1.1 Before you get started ................................................... 4

1.1.1 Shipment ................................................................ 4

1.1.2 Initial operation ....................................................... 5

1.1.3 Online registration ................................................. 5

2. CONTROL ELEMENTS ............................................... 5

2.1 Front panel ...................................................................... 5

2.2 Rear panel ....................................................................... 5

2.3 Configuration switches (MODE SWITCHES) ................. 6

2.3.1 Clip limiter ............................................................... 6

2.3.2 Input filter ............................................................... 6

2.3.3 2-channel mode (stereo) ...................................... 6

2.3.4 Parallel mode ......................................................... 6

2.3.5 Mono-bridged mode .............................................. 6

3. APPLICATIONS .......................................................... 7

3.1 Differences between 2-channel, parallel and mono

bridged operating modes ................................................ 7

3.2 Bi-amping ........................................................................ 8

4. INSTALLATION ........................................................... 9

4.1 Connections .................................................................... 9

4.1.1 Using the binding posts ....................................... 10

4.1.2 Connecting to the mains ...................................... 10

4.2 Audio connections ........................................................ 10

5. SPECIFICATIONS ..................................................... 11

6. WARRANTY .............................................................. 12

FOREWORD

Dear Customer,
welcome to the team of

BEHRINGER users, and

thank you very much for

expressing your confi-

dence in us by purchasing

this power amplifier.
Writing this foreword for

you gives me great plea-

sure, because it repre-

sents the culmination of

many months of hard

work delivered by our

engineering team to

achieve a very ambitious

goal: to develop two out-

standing power amp-

lifiers, whose flexibility

lets them respond to all

the P.A. and instrument

amplification requirements. The task of designing our new

EUROPOWER EP1500 and EP2500 certainly meant a great deal

of responsibility, which we assumed by focusing on you, the

discerning user and musician. Meeting your expectations also

meant a lot of work and night shifts. But it was fun, too. Developing

a product usually brings a lot of people together, and what a

great feeling it is when all who participated in such a project can

be proud of what theyve achieved.

It is our philosophy to share our enjoyment with you, because

you are the most important member of the BEHRINGER team.

With your highly competent suggestions for new products youve

made a significant contribution to shaping our company and making

it successful. In return, we guarantee you uncompromising quality

as well as excellent technical and audio properties at an extremely

reasonable price. All of this will enable you to give free rein to

your creativity without being hampered by budget constraints.

We are often asked how we manage to produce such high-

quality devices at such unbelievably low prices. The answer is

quite simple: its you, our customers! Many satisfied customers

mean large sales volumes enabling us to get better purchasing

terms for components, etc. Isnt it only fair to pass this benefit on

to you? Because we know that your success is our success

too!

I would like to thank all of you who have made the EUROPOWER

power amplifiers possible. You have all made your own personal

contributions, from the developers to the many other employees

at this company, and to you, the BEHRINGER user.

My friends, its been worth the effort!

Thank you very much,

Uli Behringer

1. INTRODUCTION

By purchasing one of the BEHRINGER EUROPOWER amp-

lifiers, you have selected a piece of high-end gear. This unit was

developed for professional use in live applications, and its rich

list of features will make it a dependable part of your equipment

with a diverse set of possible uses.

The EUROPOWER amps feature for example an input filter for

each channel, enabling you to remove the disturbing low-

frequency portion of the signal. Additionally, there is a limiter that

protects your loudspeakers. Various operating modes, such as

parallel or mono mode, open up various possibilities for effective

implementation with the rest of your audio equipment, leaving no

wishes unanswered.

This manual first describes the terminology used,

so that you fully understand the EUROPOWER and

its functions. Please read the manual carefully and

keep it for future reference.

1.1 Before you get started

1.1.1 Shipment

Your EUROPOWER was carefully packed at the factory, and

the packaging is designed to protect the unit from rough handling.

Nevertheless, we recommend that you carefully examine the

packaging and its contents for any signs of physical damage,

which may have occurred during transit.

If the unit is damaged, please do NOT return it to

BEHRINGER, but notify your dealer and the shipping

company immediately. Otherwise, claims for damage

or replacement may not be granted.

1. INTRODUCTION

EUROPOWER EP1500/EP2500

2. CONTROL ELEMENTS

1.1.2 Initial operation

Please make sure the unit is provided with sufficient ventilation,

and never place your EUROPOWER amp on top of other heat-

emanating equipment or in the vicinity of a heater to avoid the risk

of overheating.

The mains connection is made via the enclosed power cord

and a standard IEC receptacle. It meets all international safety

certification requirements.

Please make sure that all units have a proper ground

connection. For your own safety, never remove or

disable the ground conductor from the unit or the

AC power cord.

1.1.3 Online registration

Please do remember to register your new BEHRINGER

equipment right after your purchase by visiting

www.behringer.com (alternatively www.behringer.de) and

kindly read the terms and conditions of our warranty carefully.

Should your BEHRINGER product malfunction, our goal is to

have it repaired as quickly as possible. To arrange for warranty

service, please contact the retailer from whom the equipment

was purchased. Should your BEHRINGER dealer not be located

in your vicinity, you may directly contact one of our subsidiaries.

Corresponding contact information is included in the original

equipment packaging (Global Contact Information/European

Contact Information). Should your country not be listed, please

contact the distributor nearest you. A list of distributors can be

found in the support area of our website (www.behringer.com).

Registering your purchase and equipment with us helps us

process your repair claims quicker and more efficiently.

Thank you for your cooperation!

ATTENTION!

We would like to bring your attention to the fact

that extremely loud sound levels may damage your

hearing as well as your loudspeakers. Please lower

both GAIN controls leftwards before powering up

the unit. Be sure to keep the volume at an

appropriate level.

2. CONTROL ELEMENTS

Since control elements of both the EP1500 and the EP2500 are identical, we have used the EP1500 as the model represented in the

illustrations to assure simplicity.

2.1 Front panel

Fig. 2.1: Front panel control elements

The main switch is used to power up the amp.

Please take note: Merely switching the unit off does

not mean that it is fully disconnected from the

mains. When not using the unit for prolonged

periods of time, please unplug the units power cord

from the power outlet.

Ventilation openings are located at the front of the unit, so

that hot air is prevented from being trapped inside the unit,

thus causing faulty operation or even damage.

The

CLIP

LED lights up when the signal is distorted. Should

distortion occur, reduce the input level, so that the CLIP

LED stops lighting up.
The

SIGNAL

LED lights up as long as a signal is present

at the input.
The

GAIN

control (channels 1 and 2) is used for setting

up the input gain.
The

POWER

LED lights up as soon as the unit is powered

up.

2.2 Rear panel

Fig. 2.2: Rear panel control elements

EUROPOWER EP1500/EP2500

2. CONTROL ELEMENTS

These are the balanced XLR inputs (channels 1 and 2).
These are the stereo 1/4" TRS inputs (channels 1 and 2).

They can also be used with unbalanced plugs.
These are the

MODE

switches,

used to alter the operating

modes as well as to set the limiters and high-pass filters

(see chapter 2.3).
The units fan is located here. Fan speed adjusts

automatically to assure trouble-free operation.

To prevent faulty operation, please assure that the

unit is kept at a distance from other appliances

emanating heat.

These are the Speakon

-compatible outputs (channels 1

and 2). When running the unit in mono-bridged mode (see

chapter 2.3.5), please use the channel 1 output

exclusively. For further information on the connectors

please refer to chapter 4.1.
These are the output terminals (channels 1 and 2). When

running in mono, please make sure to use both middle

connectors to connect your loudspeaker.

BREAKER

(automated fuse). After eliminating the cause

of faulty operation, simply depress the BREAKER and

power up the unit again. The BREAKER acts in place of

common discardable fuses.

Attention: Before engaging the BREAKER switch,

you should power down the unit (POWER switch

set to OFF)!

Power is supplied via an

IEC

connector. The matching

cable is provided with the unit.

SERIAL NUMBER

of your EUROPOWER.

Here you can find a detailed overview of the individual

MODE SWITCHES functions (

2.3 Configuration switches (MODE SWITCHES)

Fig. 2.3: DIP-switches

2.3.1 Clip limiter

When the input signal connected to your amp is too high, you

end up with a distorted output signal. To prevent this, both

channels of your EUROPOWER feature a clip limiter that can be

engaged or disengaged selectively. The limiters automatically

recognize distortion and lower amplification until distortion is

reduced to a tolerable level. To preserve the dynamic

characteristics of the signal when low distortion levels are

occurring, the clip limiters function with moderate suppression.

Use switches 1 (ch. 1) and 10 (ch. 2) to activate the clip limiters.

When using broadband loudspeaker systems, the clip limiter

reduces high frequency distortions which occur when an

amplifier is overloaded. The drivers are thus protected from

being damaged.

2.3.2 Input filter

The LF (high-pass) filter removes frequencies below 30 and

50 Hz respectively. The reproduction of the signals bass portion

is thus optimized, since ultra-low, distracting frequencies are

eliminated, and more power is available for the reproduction of

the wanted segment of the signal. Engaging and disengaging the

filters is done by using the switches 3 (ch. 1) and 8 (ch. 2).

Switches 2 (ch. 1) and 9 (ch. 2) determine the cut-off frequency.

As long as the filter is disengaged, frequencies below 5 Hz are

cut to prevent damage.

You should set up the filters so they best suit the frequency

response of your speakers, since some speakers (e.g. bass

reflex speakers) are particularly sensitive to over-excursion

below the listed frequency range.

The 50 Hz filter should be engaged when using broadband

speakers because the filter provides a moderate amplification in

the 100-Hz range, resulting in a fuller sound. The 30 Hz filter is

ideally suited for subwoofer operation as well as for broadband

cabinets. The Off setting should be used only for special

applications (e.g. studio applications), in which recognizing and

subsequently removing infra-sound is important.

2.3.3 2-channel mode (stereo)

Both channels of your amp function independently from one

another in this operating mode, and each has its own input signal.

Two independent speakers are connected at the outputs. To

activate this operating mode, please set the MODE SWITCHES

4 and 5 to STEREO.

When running the unit in two-channel mode, the

switches for mono-bridged mode must be

disengaged (dip switches 6 and 7 in left position).

2.3.4 Parallel mode

Running in parallel mode enables you to feed a signal via one

of the inputs into both outputs. Each channel drives its own

loudspeaker with independent amplification, filter and limit

characteristics. To link the inputs, set the MODE SWITCHES 4

and 5 to PARALLEL INPUTS.

Mono-bridged mode switches must be dis-

engaged when running in parallel mode.

With inputs set to parallel, you can use the remaining input

connectors to feed the signal into additional amplifiers. This

means that the channel 2 inputs function as outputs.

The parallel mode is well-suited for applications in which driving

two speakers with the same signal but with separate amplification,

filter and limiter settings is desired.

2.3.5 Mono-bridged mode

This operating mode enables you to add up the respective

voltage of both channels and use it to drive a single loudspeaker.

The voltage is therefore doubled, the peak power is quadrupled,

and program power is roughly three times as high as that of the

individual channels. The input, output, gain, filter and limiter

controls belonging to channel 1 are used when running in mono-

bridged mode. The controls belonging to channel 2 are not used.

To prevent signal cancellation due to internal phase inversion,

the GAIN control belonging to channel 2 must be turned to its left-

most position.

Use this operating mode to route the power from both channels

to a single 8-Ohm or 4-Ohm load. To do so, set up the switches

6 and 7 to BRIDGE MODE ON. To use the binding posts as your

output, you MUST use the two middle posts only.

EUROPOWER EP1500/EP2500

3. APPLICATIONS

The mono-bridged mode puts added demands on

amplifier and speakers. Excessive distortion may

occasionally completely mute the amps outputs

as well as cause permanent damage to the

speakers. Please assure that your speakers

(minimal impedance 4 Ohms) as well as the cables

used can handle the extra power generated in this

mode.

3. APPLICATIONS

Running EUROPOWER amplifiers in conjunction with

8-Ohm speakers with a power rating of at least 2 x

260 Watts (EP1500) and 2 x 450 Watts (EP2500) is

recommended to assure optimal operation.

3.1 Differences between 2-channel, parallel

and mono-bridged operating modes

2-channel

mode is the most common operating mode of

amplifiers. Both channels operate fully independently from one

another. There is always a separate input signal as well as a

separate output signal.
Examples:

2-channel (stereo) playback

Two independent mono signals, e.g. instrument signal and

monitor mix

Bi-amp operation, whereby bass frequencies are run on

channel 1, and high frequencies on channel 2 (see chapter

3.2, Bi-amping).

Fig. 3.1: 2-channel mode

Fig. 3.2: DIP switch positions for 2-channel operation

Parallel mode

is identical to 2-channel mode, except for the

inputs of both channels are internally connected in parallel. One

input signal routes parallel both channels, while their filters etc.

are independently controlled.
Examples:

A mono signal is fed into both channels, whereby amplifi-

cation of each channel is controlled separately.

Parallel mode (as described above) with connection of an

additional amp via the remaining free input connector. The

input signal is present there, and may be connected to

further equipment.

When connecting a balanced input signal, please

make sure to exclusively use balanced cables for

passing the signal further on. Otherwise, a single

unbalanced cable can turn the entire signal

unbalanced.

Fig. 3.3: Parallel operation

EUROPOWER EP1500/EP2500

3. APPLICATIONS

Fig. 3.4: DIP switch positions for parallel operation

When running in

mono-bridged mode

, the voltage of both

channels is added up and fed into a single loudspeaker system.

There is one input and one output signal respectively, and only

the controls of channel 1 (and not of channel 2) are used.

However, should the DIP switches 4 and 5 still be

in PARALLEL INPUTS position while in mono-

bridged mode, the signal on the free input (input

channel 2) can be forwarded to an additional amp.

Examples:

Driving a single 8-Ohm loudspeaker.

Driving a single 4-Ohm loudspeaker.

Fig. 3.5: Mono-bridged mode

Fig. 3.6: DIP switch positions for mono-bridged mode

When the amp is overdriven for longer periods of

time, the output signal may occasionally be muted

for several seconds. In certain situations,

excessive overdriving may trigger off the

automated fuse. To avoid overdriving the amp,

please continually make sure that an appropriate

volume level is applied. CAUTION: 2-Ohm loads

should never be applied when in mono-bridged

mode.

When connecting a balanced input signal, please

make sure to exclusively use balanced cables for

passing the signal further on. Otherwise, a single

unbalanced cable can turn the entire signal

unbalanced.

Safety precautions for mono-bridged

operation

Running your amp in mono-bridged mode can quickly

result in excessive overdriving and premature shutting

down of the unit itself. In the worst-case scenario, your

loudspeakers may be damaged permanently. Therefore,

you should always make sure that the speakers you use

can indeed handle the power load fed into them.

A voltage of up to 100 V RMS is present between the

output connectors of the EP2500. Always implement

appropriate safety precautions when connecting your

speakers to avoid the risk of electric shock.

3.2 Bi-amping

By using an active crossover, you can divide up the frequency

range into several bands. For example, in doing so you can split

a mono signal into upper-frequency and lower-frequency ranges.

These two signals can then be hooked up to the inputs of your

amp, so that channel 1 amplifies the lows and channel 2 amplifies

the highs (2-channel operation). The outputs are connected to a

2-way speaker, whereby the output signal 1 drives the woofer

and output signal 2 runs the drivers. Of course, you can use two

separate speakers instead of a single 2-way speaker.

A stereo signal can also be split up analogous to the example

described above. However, to do that you need two 2-way

speakers or 4 separate speakers, two EUROPOWER amps and

an active 2-way stereo crossover. The BEHRINGER SUPER-X

PRO CX2310 is optimally suited for this task and offers

additionally a single mono-subwoofer output. By deploying a

third EP1500 amp (preferably in mono-bridged mode) and a

subwoofer, you have a perfect setup that adds a low-frequency

system to the stereo bi-amp application (see fig. 3.4). The amps

input filters for the high/mid-frequency ranges should in this

case be engaged and set at 50 Hz. To remove low, disturbing

frequencies from the signal, the input filter for the subwoofer

signal should be set at 30 Hz.

EUROPOWER EP1500/EP2500

4. INSTALLATION

The BEHRINGER EUROLIVE SERIES loudspeakers are an

outstanding solution for expanding your P.A. system, because

each frequency range/application has a speaker type that

optimally suits its characteristics.

Extreme clip limiter settings in bi-amp operating

mode can result in balance shifting.

Fig. 3.7: Stereo bi-amp mode with a separate subwoofer

4. INSTALLATION

Your EUROPOWER can be installed into a 19" rack and requires

two rack units. Please use four attaching screws and washers

for installation. Reinforce the back end, especially for on-the-

road use. Please assure that enough cool air reaches the rack,

especially when other rack equipment emanates a lot of heat. In

the case of the EUROPOWER EP1500 and EP2500, hot air

circulates at the front of the unit to thermally relieve the rack

enclosure.

Fan speed adjusts automatically and assures safe

operation. Never block ventilation openings. Should

internal temperature reach extreme values, the

unit will shut down automatically.

4.1 Connections

Inputs

Each channel features balanced XLR and 1/4" TRS stereo jack

inputs, with input impedances of 20 k

Ω

(balanced) and 10 k

Ω

(unbalanced). In general, balanced signals cause less noise

than unbalanced signals.

For balanced input signals, use the XLR and 1/4" TRS stereo

inputs. For unbalanced input signals, use the unused pin of the

XLR connector with grounding. No alteration is necessary on

mono jack connectors (see plug type illustrations on page 10).

Should you register distractive signals such as

noise or hissing, we recommend separating the

amp input from the signal source. This way, you

can quickly determine if the noise originates in

the equipment connected to the amp. Always

make sure to completely lower amplification of

both channels before powering up the amp (GAIN

control turned all the way leftward). Otherwise,

permanent damage to your speakers may occur.

Outputs

Your EUROPOWER offers several output connection possi-

bilities: two Neutrik

Speakon

®-

-compatible connectors and two

pairs of touch-safe binding posts. The Speakon

connectors

were especially developed for driving high-power speakers.

They snap in securely, prevent electric shock and assure correct

polarity. The upper connector drives either one or both channels,

and is therefore well-suited for mono-bridged operation (1+/2+).

The lower connector carries the signals from channel 2 only.

Fig. 4.1: Neutrik

Speakon

-compatible connectors

Whenever possible, use thick and short speaker

cables to minimize power losses. Never lay out

output cables near input cables.

EUROPOWER EP1500/EP2500

4. INSTALLATION

4.1.1 Using the binding posts

To connect the loudspeakers to the amplifiers binding posts,

please do the following:
1.

Switch off the amp and disconnect it from the mains (unplug

mains connector).

Remove the protective plastic covers shielding the binding

posts by loosening the two screws on the right-hand side

of the connections and lift the plastic cover upwards.

Attach the terminal of your loudspeaker cable to the corres-

ponding binding post.

Place the protective plastic covers into its original upright

position on each binding post and replace the two screws.

Never operate the device without the protective

plastic covers in place!

Fig 4.2: Protective plastic covers shielding the binding posts

When using binding post connectors, please make sure that

insulation on cables is not removed too high. Insert the naked

part of the cable fully so that no metal is visible. Cable clamps

must be isolated to avoid the possibility of electric shock. When

running the amp in mono-bridged mode, always use the middle

two binding post connectors, paying attention to correct polarity.

ATTENTION! If you notice naked cable endings on

the binding post connectors, do not power up the

amp because of the risk of electric shock.

4.1.2 Connecting to the mains

Always connect your EUROPOWER amplifier to the voltage

specified on the rear of the device. Connecting the amp to an

incorrect voltage can permanently damage your amp.

Before powering up the amplifier, double-check all

connections and fully lower the gain setting.

4.2 Audio connections

Various cables are needed for different types of applications.

The following illustrations show the correct wiring. Always use

high-grade cables.

When connecting a balanced input signal, please

make sure to exclusively use balanced cables for

passing the signal further on. Otherwise, one

single unbalanced cable can turn the entire signal

unbalanced.

Fig. 4.3: XLR connections

Fig. 4.4: 1/4" TS connector

Fig. 4.5: 1/4" TRS connector

EUROPOWER EP1500/EP2500

5. SPECIFICATIONS

BEHRINGER makes every effort to ensure the highest standard of quality. Necessary modifications are carried out without notice. Thus, the

specifications and design of the device may differ from the information given in this manual.

5. SPECIFICATIONS

28738732:(5

20 Hz - 20 kHz @ 0.1% THD, both channels driven:

Ω

per channel

260 W

450 W

Ω

per channel

400 W

650 W

1 kHz @ 0.1% THD, both channels driven:

Ω

per channel

280 W

500 W

Ω

per channel

450 W

750 W

Ω

per channel

700 W

1200 W

Bridged Mono:

Ω

, 20 Hz - 20 kHz, 0.1% THD

800 W

1300 W

Ω

, 1 kHz, 0.1% THD

900 W

1500 W

Ω

, 1 kHz, 1% THD

1400 W

2400 W

',67257,21

< 0.01%

< 0.02%

)5(48(1&<5(63216(

(at 10 dB below rated output power)

'$03,1*)$&725
12,6(XQZHLJKWHG+]WRN+]
92/7$*(*$,1

40 x (32 dB)

50 x (34 dB)

,13876(16,7,9,7<9506

(@ 8

Ω

)

1.15 V (+3.4 dBu)

1.23 V (+4.0 dBu)

,1387,03('$1&(
&21752/6

Front:

Rear:

,1',&$7256

&211(&7256

Inputs:

Outputs

&22/,1*
$03/,),(53527(&7,21

/2$'3527(&7,21

287387&,5&8,77<3(

Class AB complementary linear

output

Class H complementary linear output

32:(56833/<

Mains voltage

Breaker

Mains connector

Power consumption

3.5 A (230 V~, 50 Hz)

5 A (230 V~, 50 Hz)

6.7 A (120 V~, 60 Hz)

9.6 A (120 V~, 60 Hz)

',0(16,216:(,*+7

Dimensions (H x W x D)

Weight

approx. 15.7 kg (34.6 Ibs)

approx. 16.6 kg (36.6 Ibs)

15 A 100 - 120 V

20 Hz - 20 kHz, +0/-1 dB

5 Hz - 50 kHz (at -3 dB points)

Power switch, gain control (channels 1 and 2)

DIP switches (10 x)

10 k

Ω

(unbalanced), 20 k

Ω

(balanced)

> 300 @ 8

Ω

-100 dB

POWER: green LED

CLIP: red LED, 1 per channel

SIGNAL: yellow LED, 1 per channel

Balanced XLR and 1/4" TRS connectors

approx. 3 1/2" (88 mm) x 19" (482.6 mm) x 15 4/5" (402 mm)

Turn-on/off muting, AC coupling

USA/Canada 120 V~, 60 Hz

Europe/U.K./Australia 230 V~, 50 Hz

Japan 100 V~, 50 - 60 Hz

General export model 120/230 V~, 50 - 60 Hz

8 A 200 - 230 V

Standard IEC receptacle

China 220 V~, 50 Hz

“Touch-Proof” binding posts and Speakon

-compatible connectors

Continuously variable speed fan, back-to-front air flow

Full short circuit, open circuit, thermal and HF protection

Stable into reactive or mismatched loads

EUROPOWER EP1500/EP2500

6. WARRANTY

Technical specifications and appearance subject to change without notice. The information contained herein is correct at the time of printing. The names

of companies, institutions or publications pictured or mentioned and their respective logos are registered trademarks of their respective owners. Their use

neither constitutes a claim of the trademarks by BEHRINGER

nor affiliation of the trademark owners with BEHRINGER

. BEHRINGER

accepts no

liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained

herein. Colours and specification may vary slightly from product. Products are sold through our authorised dealers only. Distributors and dealers are not

agents of BEHRINGER

and have absolutely no authority to bind BEHRINGER

by any express or implied undertaking or representation. No part of this

manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for

any purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH. BEHRINGER

is a registered trademark.

Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany.

Tel. +49 2154 9206 0, Fax +49 2154 9206 4903

6. WARRANTY

§ 1 OTHER WARRANTY RIGHTS AND NATIONAL LAW

1. This warranty does not exclude or limit the buyers statutory

rights provided by national law, in particular, any such rights

against the seller that arise from a legally effective purchase

contract.

2. The warranty regulations mentioned herein are applicable

unless they constitute an infringement of national warranty law.

§ 2 ONLINE REGISTRATION

Please do remember to register your new BEHRINGER

equipment right after your purchase by visiting

www.behringer.com (alternatively www.behringer.de) and

kindly read the terms and conditions of our warranty carefully.

Registering your purchase and equipment with us helps us

process your repair claims quicker and more efficiently.

Thank you for your cooperation!

§ 3 WARRANTY

1. BEHRINGER (BEHRINGER International GmbH including all

BEHRINGER subsidiaries listed on the enclosed page, except

BEHRINGER Japan) warrants the mechanical and electronic

components of this product to be free of defects in material and

workmanship for a period of one (1) year* from the original date

of purchase, in accordance with the warranty regulations

described below. If the product shows any defects within the

specified warranty period that are not excluded from this

warranty as described under § 5, BEHRINGER shall, at its

discretion, either replace or repair the product using suitable

new or reconditioned parts. In the case that other parts are used

which constitute an improvement, BEHRINGER may, at its

discretion, charge the customer for the additional cost of these

parts.

2. If the warranty claim proves to be justified, the product will

be returned to the user freight prepaid.

3. Warranty claims other than those indicated above are

expressly excluded.

§ 4 RETURN AUTHORIZATION NUMBER

1. To obtain warranty service, the buyer (or his authorized

dealer) must call BEHRINGER (see enclosed list) during normal

business hours

BEFORE

returning the product. All inquiries must

be accompanied by a description of the problem. BEHRINGER

will then issue a return authorization number.

2. Subsequently, the product must be returned in its original

shipping carton, together with the return authorization number to

the address indicated by BEHRINGER.

3. Shipments without freight prepaid will not be accepted.

§ 5 WARRANTY REGULATIONS

1. Warranty services will be furnished only if the product is

accompanied by a copy of the original retail dealers invoice.

Any product deemed eligible for repair or replacement under the

terms of this warranty will be repaired or replaced.

2. If the product needs to be modified or adapted in order to

comply with applicable technical or safety standards on a national

or local level, in any country which is not the country for which

the product was originally developed and manufactured, this

modification/adaptation shall not be considered a defect in

materials or workmanship. The warranty does not cover any

such modification/adaptation, irrespective of whether it was

carried out properly or not. Under the terms of this warranty,

BEHRINGER shall not be held responsible for any cost resulting

from such a modification/adaptation.

3. Free inspections and maintenance/repair work are expressly

excluded from this warranty, in particular, if caused by improper

handling of the product by the user. This also applies to defects

caused by normal wear and tear, in particular, of faders,

crossfaders, potentiometers, keys/buttons, tubes, guitar strings,

illuminants and similar parts.

4. Damages/defects caused by the following conditions are

not covered by this warranty:

improper handling, neglect or failure to operate the unit in

compliance with the instructions given in BEHRINGER user

or service manuals.

connection or operation of the unit in any way that does not

comply with the technical or safety regulations applicable in

the country where the product is used.

damages/defects caused by force majeure or any other

condition that is beyond the control of BEHRINGER.

5. Any repair or opening of the unit carried out by unauthorized

personnel (user included) will void the warranty.

6. If an inspection of the product by BEHRINGER shows that

the defect in question is not covered by the warranty, the

inspection costs are payable by the customer.

7. Products which do not meet the terms of this warranty will

be repaired exclusively at the buyers expense. BEHRINGER will

inform the buyer of any such circumstance. If the buyer fails to

submit a written repair order within 6 weeks after notification,

BEHRINGER will return the unit C.O.D. with a separate invoice

for freight and packing. Such costs will also be invoiced

separately when the buyer has sent in a written repair order.

§ 6 WARRANTY TRANSFERABILITY

This warranty is extended exclusively to the original buyer

(customer of retail dealer) and is not transferable to anyone

who may subsequently purchase this product. No other person

(retail dealer, etc.) shall be entitled to give any warranty promise

on behalf of BEHRINGER.

§ 7 CLAIM FOR DAMAGES

Failure of BEHRINGER to provide proper warranty service shall

not entitle the buyer to claim (consequential) damages. In no

event shall the liability of BEHRINGER exceed the invoiced value

of the product.

* Customers in the European Union please contact BEHRINGER

Germany Support for further details.

PDF User Manual

EUROPOWER EP2500

Full Text Searchable PDF User Manual