Indesit WIA 82 Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

English

Contents

Installation, 14-15

Unpacking and levelling, 14

Electric and water connections, 14-15

The first wash cycle, 15

Technical details, 15

Washing machine description, 16-17

Control panel, 16

Leds, 17

Starting and Programmes, 18

Briefly: how to start a programme, 18

Programme table, 18

Personalisations, 19

Setting the temperature, 19

Functions, 19

Detergents and laundry, 20

Detergent dispenser, 20

Preparing your laundry, 20

Special items, 20

Precautions and advice, 21

General safety, 21

Disposal, 21

Saving energy and respecting the environment, 21

Care and maintenance, 22

Cutting off the water or electricity supply, 22

Cleaning your appliance, 22

Cleaning the detergent dispenser, 22

Caring for your appliance door and drum, 22

Cleaning the pump, 22

Checking the water inlet hose, 22

Troubleshooting, 23

Service, 24

Before calling for Assistance, 24

WASHING MACHINE

WIA 82

Instructions for use

Installation

Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washing machine to inform

the new owner as to its operation and features.

Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

3. Remove the 3

protective screws and

the rubber washer with

the respective spacer,

situated on the rear of

the appliance

(see

figure)

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again if the

washing machine needs to be moved to another

location.

Packaging materials are not children's toys.

Levelling

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or

loosening the adjustable

front feet

(see figure)

;

the angle of inclination,

measured according to

the worktop, must not

exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose

and screw the latter

onto a cold water tap

with a 3/4 gas threaded

mouth

(see figure)

Before making the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure)

3. Make sure there are no kinks or bends in the

hose.

The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page)

If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

Service

oubleshooting

Precautions

Care

Programmes

Detergents

Installation

Description

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from

the floor;

alternatively, place it

over the edge of a

basin, sink or tub,

fastening the duct

supplied to the tap

(see

figure)

. The free end of

the hose should not be

underwater.

We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

the socket is earthed and in compliance with the

applicable law;

the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table

(on the right)

;

the supply voltage is included within the values i

ndicated on the Technical details table

(on the right)

;

the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

When the washing machine is installed, the mains

socket must be within easy reach.

Do not use extensions or multiple sockets.

The power supply cable must never be bent or

dangerously compressed.

The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, setting the 90°C

programme without a pre-wash cycle.

65 - 100 cm

Technical details

Model

WIA 82

Dimensions

59.5 cm wide

85 cm high
52,5 cm deep

Capacity

from 1 to 5 kg

Electric

connections

voltage 220/230 Volts 50 Hz

maximum absorbed power 1850 W

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)
drum capacity 46 litres

Spin speed

up to 800 rpm

Control
programmes

according to

IEC456 directive

programme 3; temperature 60°C;

run with a load of 5 kg.

This appliance is compliant with the
following European Community

Directives:

- 73/23/CEE of 19/02/73 (Low

Voltage) and subsequent amendments

- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and

subsequent amendments

Washing machine description

Control panel

Detergent dispenser

TEMPERATURE

Knob

PROGRAMME/

ON-OFF

Knob

Leds

FUNCTION

Buttons

DOOR

LOCK

Led

Detergent dispenser:

to add detergent and fabric

softener

(see page 20).

LEDS:

to find out which wash cycle phase is under

way.

FUNCTION

buttons: to select the functions

available. The button corresponding to the function

selected will remain on.

TEMPERATURE

knob: to set the temperature or

the cold wash cycle

(see page 19)

DOOR LOCK

Led: to find out whether the washing

machine is on and if the appliance door can be

opened

(see page 17)

START/PAUSE

button: starts or temporarily

interrupts programmes.

N.B.:

once the programme has started, pressing this

button will stop the cycle and only the LED for the

cycle phase in progress will light up. After about 1

minute you will be able to open the door (when the

DOOR LOCK led switches off). If the DOOR LOCK

led stays lit, it means that there is something that

needs to be checked before the door is opened

(e.g.: there is water in the tub or the temperature of

the water is too high).

Pressing the button again restarts the programme

from the point at which it was interrupted.

PROGRAMME/ON-OFF

knob: sets the desired

programme

(see page 18)

and switches the machine

on or off.

The knob stays still during the cycle.

START/

PAUSE

Button

Service

oubleshooting

Precautions

Care

Programmes

Detergents

Installation

Description

DOOR LOCK led:

If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages,

wait for the LED to flash before you open the appliance door.

The rapid flashing of the DOOR LOCK Led together with the flashing of at least one other LED indicates there is

an abnormality. Call for Technical Assistance.

Leds

The LEDS provide important information.

This is what they can tell you:

Cycle phase under way:

During the wash cycle, the LEDs gradually illuminate

on to indicate the cycle phase under way:

Prewash/Wash

Rinse

Spin cycle

Note: during draining, the LED corresponding to the

Spin cycle phase will be turned on.

Function buttons

The FUNCTION BUTTONS also act like LEDS.

When a function is selected, the corresponding

button is illuminated.

If the function selected is incompatible with the

programme set, the button will flash and the

function will not be enabled.

If you set a function that is incompatible with

another function you selected previously, only the

last one selected will be enabled.

Type of fabric and degree of soil Program-

mes

Wash

temperat.

Detergent

Fabric

softener

Cycle

length

(minutes)

Description of wash cycle

Pre-

wash Wash

Cottons

Extremely soiled whites

(sheets, tablecloths, etc.)

Max

160

Pre-wash, wash cycle, rinse cycles,

intermediate and final spin cycles

Extremely soiled whites

(sheets, tablecloths, etc.)

Max

143

Wash cycle, rinse cycles, intermediate

and final spin cycles

Heavily soiled whites and fast

colours

60°C

127

Wash cycle, rinse cycles, intermediate

and final spin cycles

Slightly soiled whites and delicate

colours (shirts, jumpers, etc.)

40°C

Wash cycle, rinse cycles, intermediate

and final spin cycles

Synthetics

Heavily soiled fast colours

(baby linen, etc.)

60°C

Wash cycle, rinse cycles, anti-crease or

delicate spin cycle

Heavily soiled fast colours

(baby linen, etc.)

50°C

Wash cycle, rinse cycles, anti-crease or

delicate spin cycle

Delicate colours (all types of

slightly soiled garments)

40°C

Wash cycle, rinse cycles, anti-crease or

delicate spin cycle

Delicate colours (all types of

slightly soiled garments)

30°C

Wash cycle, rinse cycles and delicate

spin cycle

Delicates

Wool

40°C

Wash cycle, rinse cycles, anti-crease

and delicate spin cycle

Very delicate fabrics

(curtains, silk, viscose, etc.)

30°C

Wash cycle, rinse cycles, anti-crease or

draining cycle

PARTIAL PROGRAMMES

Rinse

Rinse cycles and spin cycle

Delicate rinse cycle

Rinse cycles, anti-crease or draining

Spin cycle

Draining and heavy duty spin cycle

Delicate spin cycle

Draining and delicate spin cycle

Draining

Starting and Programmes

Programme table

Briefly: starting a programme

1. Switch on the washing machine by turning the

PROGRAMME/ON-OFF knob to the desired

programme.

All the LEDS will light up for a few seconds and

the DOOR LOCK Led will begin to flash.

2. Load your laundry into the washing machine and

shut the appliance door.

3. Set the wash temperature

(see page 19)

4. Add the detergent and any fabric softener

(see page 20)

5. Start he programme by pressing the START/PAUSE

button.

If you want to cancel the cycle set, turn the

PROGRAMME/ON-OFF knob to the

position

and wait for all the LEDs to illuminate and then

turn off again.

If another programme is not selected, the DOOR

LOCK led will remain lit for about 1 minute.

6. When the programme is finished, the DOOR

LOCK Led will flash to indicate that the

appliance door can be opened. Take out your

laundry and leave the appliance door ajar to allow

the drum to dry thoroughly.

Switch the washing machine off by turning the

PROGRAMME/ON-OFF knob to the

position.

Notes

For the anti-crease function, please see

page 19

. The information contained in the table is purely indicative.

Special programme

Daily

(programme 8 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30

minutes and allows you to save on both time and energy. By setting this programme (8 at 30°C), you can wash

different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.

We recommend the use of liquid detergent.

Service

oubleshooting

Precautions

Care

Programmes

Detergents

Installation

Description

Personalisations

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature

(see Programme table on page 18)

The temperature can be lowered, or even set to a cold wash ( ).

Functions

To enable a function:

1. press the button corresponding to the desired function, according to the table below;

2. the function is enabled when the corresponding button is illuminated.

Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the

programme set.

Function

Effect

Comments

Enabled with

programmes:

Rapid

Cuts the duration

of the wash cycle

by 30%.

1, 2, 3, 4,

5, 6, 7

Extra Rinse

Increases the

efficiency of the

rinse.

Recommended when the appliance has a full load or with large

quantities of detergent.

1, 2, 3, 4, 5,

6, 7 and

Rinse cycles.

Spin

exclusion

The washing

machine will not

carry out a spin

cycle, but rather

a drum spin at

medium speed to

assist water

draining.

We recommend that you use it when washing garments which are

difficult to iron.

All

programmes

except for 10

and draining.

Anti-crease

This function interrupts the wash programme, and the washing is left to soak in water before the appliance is drained. It is

enabled in programmes 5 - 6 - 7 - 9- 10 and Delicate rinse cycle.

To conclude the cycle, press the START/PAUSE button.

To run the draining cycle alone, set the knob to the relative symbol

and press the START/PAUSE button.

Detergent dispenser

Good washing results also depend on the correct

dose of detergent: adding too much detergent won't

necessarily make for a more efficient wash, and may

in fact cause build up on the interior of your

appliance and even pollute the environment.

Open up the detergent

dispenser and pour in

the detergent and fabric

softener, as follows.

compartment 1: Detergent for pre-wash

(powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in

immediately prior to the wash cycle start.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow from the grid.

Do not use hand wash detergent because it may

form too much foam.

Preparing your laundry

Divide your laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from

whites.

Empty all pockets and check for loose buttons.

Do not exceed the weight limits stated below,

which refer to the weight when dry:

Sturdy fabrics: max 5 kg

Synthetic fabrics: max 2.5 kg

Delicate fabrics: max 2 kg

Wool: max 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1,200 g

1 towel 150-250 g

Special items

Curtains:

fold curtains and place them in a pillow

case or mesh bag. Wash them separately without

exceeding half the appliance load. Use programme

10 which excludes the spin cycle automatically.

Quilted coats and windbreakers:

if they are

padded with goose or duck down, they can be

machine-washed. Turn the garments inside out and

load a maximum of 2-3 kg, repeating the rinse cycle

once or twice and using the delicate spin cycle.

Trainers:

remove any mud. They can be washed

together with jeans and other tough garments, but

not with whites.

Wool:

for best results, use a specific detergent,

taking care not to exceed a load of 1 kg.

Detergents and laundry

Precautions and advice

Service

oubleshooting

Precautions

Care

Programmes

Detergents

Installation

Description

The washing machine was designed and built in

compliance with the applicable international safety

regulations. The following information is provided for

your safety and should consequently be read

carefully.

General safety

This appliance has been designed for non-

professional, household use and its functions must

not be changed.

This washing machine should only be used by

adults and in accordance with the instructions

provided in this manual.

Never touch the washing machine when barefoot

or with wet or damp hands or feet.

Do not pull on the power supply cable to unplug

the appliance from the electricity socket. Pull the

plug out yourself.

Do not open the detergent dispenser while the

appliance is in operation.

Do not touch the drain water as it could reach

very high temperatures.

Never force the washing machine door: this could

damage the safety lock mechanism designed to

prevent any accidental openings.

In the event of a malfunction, do not under any

circumstances touch internal parts in order to

attempt repairs.

Always keep children well away from the

appliance while in operation.

The appliance door tends to get quite hot during

the wash cycle.

Should it have to be moved, proceed with the

help of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

Before loading your laundry into the washing

machine, make sure the drum is empty.

Disposal

Disposing of the packaging material:

observe local regulations, so the packaging can

be re-used.

Disposing of an old washing machine:

before scrapping your appliance, cut the power

supply cable and remove the appliance door.

Saving energy and respecting the

environment

Environmentally-friendly technology

If you only see a little water through your appliance

door, this is because thanks to the latest Indesit

technology, your washing machine only needs less

than half the amount of water to get the best

results: an objective reached to respect the

environment.

Saving on detergent, water,

energy and time

To avoid wasting resources, the washing machine

should be used with a full load. A full load instead

of two half loads allows you to save up to 50% on

energy.

The pre-wash cycle is only necessary on

extremely soiled garments. Avoiding it will save on

detergent, time, water and between 5 and 15%

energy.

Treating stains with a stain remover or leaving

them to soak before washing will cut down the

need to wash them at high temperatures. A

programme at 60°C instead of 90°C or one at

40°C instead of 60°C will save up to 50% on

energy.

Use the correct quantity of detergent depending

on the water hardness, how soiled the garments

are and the amount of laundry you have, to avoid

wastage and to protect the environment: despite

being biodegradable, detergents do contain

ingredients that alter the natural balance of the

environment. In addition, avoid using fabric

softener as much as possible.

If you use your washing machine from late in the

afternoon until the early hours of the morning, you

will help reduce the electricity board's peak load.

If your laundry has to be dried in a tumble dryer,

select a high spin speed. Having the least water

possible in your laundry will save you time and

energy in the drying process.

Care and maintenance

Cutting off the water or electricity

supply

Turn off the water tap after every wash. This will

limit the wear of your appliance's water system

and also prevent leaks.

Unplug your appliance when cleaning it and

during all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance can

be cleaned with a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

Remove the dispenser

by pulling it out

(see

figure)

Wash it under running

water; this operation

should be repeated

frequently.

Caring for your appliance door and

drum

Always leave the appliance door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump that does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber that protects the

pump, situated in the lower part of the same.

Make sure the wash cycle has ended and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front of the

washing machine

(see

figure)

;

2. unscrew the lid

rotating it anti-

clockwise

(see figure)

: a

little water may trickle

out. This is perfectly

normal;

3. clean the interior thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If

you see any cracks, replace it immediately: during

the wash cycles, water pressure is very strong and

a cracked hose could easily split open.

Never use hoses that have already been used.

Troubleshooting

Service

oubleshooting

Precautions

Care

Programmes

Detergents

Installation

Description

Your washing machine could fail to work. Before calling for Assistance

(see page 24)

, make sure the problem

can't easily be solved by consulting the following list.

Problem

The washing machine won't

start.

The wash cycle won't start.

The washing machine fails to

load water.

The washing machine

continuously loads and unloads

water.

The washing machine does not

drain or spin.

The washing machine vibrates

too much during the spin cycle.

The washing machine leaks.

The DOOR LOCK Led flashes

rapidly at the same time as at

least one other LED.

There is too much foam.

Possible causes/Solution:

The appliance is not plugged into the socket, or not enough to

make contact.

There has been a power failure.

The appliance door is not shut properly.

The START/PAUSE button has not been pressed.

The water tap is not turned on.

The water inlet hose is not connected to the tap.

The hose is bent.

The water tap is not turned on.

There is a water shortage.

The water pressure is insufficient.

The START/PAUSE button has not been pressed.

The drain hose is not fitted between 65 and 100 cm from the floor

(see page 15)

The free end of the hose is underwater

(see page 15)

The wall drainage system doesn't have a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and call for Assistance. If the dwelling is on one of

the upper floors of a building, there may be drain trap problems causing the

washing machine to load and unload water continuously. In order to avoid

such an inconvenience, special anti-drain trap valves are available in shops.

The programme does not foresee the draining: some programmes

require enabling the draining manually

(see page 18)

The Anti-crease function is enabled: to complete the programme,

press the START/PAUSE button

(see page 19)

The drain hose is bent

(see page 15)

The drain duct is clogged.

The drum was not unblocked correctly during installation

(see page 14)

The washing machine is not level

(see page 14)

The washing machine is closed in between furniture cabinets and

the wall

(see page 14)

The water inlet hose is not screwed on correctly

(see page 14)

The detergent dispenser is obstructed (to clean it,

see page 22)

The drain hose is not secured properly

(see page 15)

Call for Assistance because this means there is an abnormality.

The detergent is not suitable for machine washing (it should bear

the definition "for washing machines" or "hand and machine wash",

or the like).

You used too much detergent.

Before calling for Assistance:

Check whether you can solve the problem on your own

(see page 23)

;

Restart the programme to check whether the problem has been solved;

If this is not the case, contact an authorised Technical Service Centre on the telephone number

provided on the guarantee certificate.

Always request the assistance of authorised servicemen.

Notify the operator of:

the type of problem;

the appliance model (Mod.);

the serial number (S/N).

This information can be found on the data plate situated on the rear of the washing machine.

Service