Full Text Searchable PDF User Manual
WHEELSETS
W-SERIES
HUBS
HiTORQUE
with Syntace MicroAdjust Caps
SYNTACE WHEELS W-SERIES
Congratulations on your new Syntace wheelset. You have made a good choice.
Your wheelset has been manufactured to the highest standards and assembled with upmost care. However,
in order to maintain the very highest performance and long lifespan it is important to take note of following
and care for it accordingly.
Keep in mind that all parts relevant for the safety on your bike have an “elephantine” memory: any damage
(through crashes or overload), even if long ago, will add up over the lifetime of the product.
Tip: take note of the Syntace crash replacement offer.
Intended use
Ensure that your selected model of Synace wheels (dimensions of your frame and fork) and components (rim
tape, tube, valve, tyre, brakes, cassette) used in combination with the wheels are compatible with your bike.
All Syntace MTB wheels are intended for use on bicycles.
The W25 and W30 rims are intended for use up to and including All-Mountain riding. The W35 and W40 rims
are intended for use up to and including Enduro style riding.
The Syntace wheels are not intended for use in Freeride and Downhill applications. If you wish to use the
Syntace wheels in such an application you will have to accept that they are less dent resistant than conside-
rably heavier rims which are specifically intended for these applications.
For everything but Downhill
Through several years of experience we can say: Syntace W-Series wheels can do everything except from
resisting deliberately caused pinch flats with a Maxxis Minion or Specialized Butcher tyres (or similar). What
we mean, is causing harsh pinch flats using a tyre with a knob profile which is unfavourable towards wide
rims. Doing this, will simply dang up the rim hook. And we will have to help out with a crash replacement.
2
Compatability:
• Please check your wheel’s compatability as outlined in the attachment, page 12.
• Please use only rim tape, tubes and tyres that correspond to the wheel’s ETRTO/ISO diemsions.
• Only compatible with disc brakes with a 6 bolt pattern.
• The Syntace MTB wheelset is not for use with rim brakes.
• The rims will come with drilling for a Presta valve. Should you require a Schrader valve, rims can be drilled
to a maximum of 8.5mm.
Assembly with tubes
• First apply the rim tape to the rim as outlined by the manufacturer.
Tip: we recommend an adhesive rim tape (such as Schwalbe 15mm).
• Now assemble tube and tyre as per manufacturer’s instructions.
Tip: in order to not pinch the tube, we recommend avoiding the use of a tyre lever.
• First lift the first side of the tyre onto the rim.
• Then, put the slightly inflated tube between tyre and rim and work the second tyre side onto the rim starting
from the opposite end of the valve. This will ensure the tyre can sit in the central rim well and can be moun-
ted easily by hand. Now work the tyre around evenly on both sides towards the valve. For easiest assembly,
ensure that the tyre really sits in the central rim well. Like this you will be able to assemble most tyres
without needing tyre levers. If you still need tyre levers however, please ensure you use plastic ones.
• Take note of the recommended pressures of the tyre manufacturers.
• Assemble brake rotors and cassette (grease freewheel body!) according to manufacturer’s instructions.
• Now you can put the wheels in your bike. Please take note of the Syntace Hi-Torque hub owner’s manual as
well as the manufacturer’s instructions from your selected skewers or through axles.
Tubeless assembly
All Syntace MTB wheels can be used with „tubeless ready“ tyres without the use of a tube.
For the W25 and W30, use a valve with conical valve seat. You will need to drill
out (only!) the inner rim hole to 7.5 - 8.0mm. When done, debur.
Conically sealing valve models are available from manufactuerers such as
NoTubes (see below).
Alternatively, if you do not wish to drill the inner rim hole, you can use tubeless
valves with flat sealing rubber seal such as available from American Classic or
Bontrager (see below).
Take note: This is only possible with W35 and W40.
3
4
Applying tubeless rim tape
Before applying the tubeless rim tape, clean and degrease the rim well thouroughly with with a cleaning
alcohol.
Recommended rim tapes:
• Syntace W25: Yellowtape 21mm
• Syntace W30: Yellowtape 30mm
• Syntace W35: Tesa strapping tape 4289 30mm width, or Yellowtape 25mm overlapping*
• Syntace W40: Tesa strapping tape 4289 30mm width overlapping, or Yellowtape 25mm overlapping*
*For W35 and W40 the 25mm Yellowtape can be used. However, it is to be applied in two overlapping layers
so that the entire rim bed is covered, one layer to the right rim wall and the other to the left rim wall.
Apply the tape tightly and free of air bubbles.
Overlap the tape approx. 10 – 15mm at the ends.
Poke hole for valve, push the valve through and tighten nut.
Mount tyre as per usual and fill the tyre with sealant through the valve by unscrewing the valve core. Alterna
-
tively you can put only one side of the tyre on the rim, pour the sealant into the tyre directly and then mount
the remaining tyre on the rim and pump up to 2.5 bar with a compressor to seat the tyre. Hold the wheel with
both hands and both shake and rotate to distribute the sealant on the entire inner surface of the tyre.
Further tips to tubeless setups can be found on:
http://www.youtube.com/watch?v=-kYzIWln99E (German)
http://www.youtube.com/watch?v=T-OVi2ssvms (English)
Search for: Schwalbe, Tubeless ready, assembly instructions.
5
Tyre pressure
As our recommendation of tyre width results in a tyre carcass which sits on the rim in a much more upright
fashion, you can run thinner/lighter sidewalls and use a lower tyre pressure.
So if you have a W30, W35 or W40 wheelset and use the tyre pressures we recommend, then procede as
follows:
Reduce the tyre pressure from the minimum tyre pressure as recommended by the tyre manufacturer by in
steps of 0.1 bar (or approx 1 psi) and test on a regular trail as to how it behaves and feels until your personal
favourite min. Tyre pressure is found.
Tip: On the front we have found tyre pressures of 1.0 – 1.5 bar (approx. 14.5 – 21.8) to give best results and
on the rear we have found tyre pressures of 1.2 – 1.8 bar (17.4 – 26.1psi) to give best results.
Maintenance, care and safety
Correct fitting, maintenance and care guarantees a long lifespan, durability and dependable function of your
Syntace components.
Follow these simple steps:
• All information regarding Syntace hubs can be found in the owners manual accompanying the hubs.
• Check your spoke tension reguarly. Too low spoke tension will cause individual spokes to be over stressed
which will result in a higher risk of spoke failure, and your wheels becoming out of true.
• Do not clean the hubs with a high pressure water stream such as achieved with a high pressure cleaner!
When cleaning the hubs with a high pressure water stream, water and dirt can enter the bearings. This will
quickly result in damaged bearings and will require replacing them.
• Check tyre pressure regularly.
• If truing is required, please take your wheels to an experienced wheel builder.
• If truing is required, apply a thin thread locker such as Loxeal 70-14 or DT Swiss Spoke Freeze, as the initial
bond between nipple and spoke is broken when turning the nipple.
Syntace Disc Shims are recommended for aligning the brake rotor. They will allow perfect alignment of your
rotor within the brake caliper.They are also useful for aligning the brake rotor in the same position on multiple
wheelsets so no more brake drag is experienced or re-positioning of caliper is neccesary. Item no. 102675 |
Set of 8, 0.2mm thickness / each. Intl. Standard 6 hole pattern.
6
HITORQUE HUBS
Keep in mind that all parts relevant for the safety on your bike have an “elephantine” memory. They will re-
member any damage (crashes, overloading, etc.), regardless of how long ago they occurred and will add up
over the lifespan of the component. We at Syntace, have built in a proper amount of “Overload Safety” into
all our components. Damaged components should under no circumstance be straightened or repaired, but
immediately replaced. Otherwise the component may fail and a crash with serious injury could result.
Tip: take note of the Syntace crash replacement offer.
Intended use
Ensure that your Syntace hubs are compatible with your bike (dimensions of your frame and fork, brakes,
cassette, rims).
All Syntace MTB hubs are intended for use on bicycles.
The Syntace hubs have no restrictions when used on a bicycle and can be used for Downhill use.
Compatability
• The compatability of the hubs concerning hub/axle standard can be found in the hub compatability section
at the end of the owner’s manual.
• Only compatible with disc brake rotors with a 6 bolt pattern.
Assembly
• All Syntace hubs are supplied ready for assembly. The axial play may need to be adjusted when first as
-
sembling in your bike. Exact procedure for this can be found in section „Adjust axial play“.
• In case you require other end caps for your Syntace hubs, please take note of following sections in this
manual: „Hub configuration“ and „Changing end caps“.
7
Hub configuration
For a long lifetime of bearings, it is important that no axial forces are applied to the bearings. A slight axial
play of up to 0.1mm is always better than too much axial pressure on the bearings!
All Syntace hubs use non stepped axles without spacer tubes between the bearings. This allows the correc-
tion of the tolerances that add up when many components are assembled together which otherwise would not
be possible.
What does this mean? The Syntace hub components are all stuck onto one shoulderless axle (smooth,
continuous outer diameter). This assures that all components can be assembled on the axle without any
play, and no axial pressure is applied to the bearings due to the unavoidable tolerances of all the individual
components.
Both end caps are pressed onto the axle.
The adjustable end cap consists of three components: a bronze coloured outer adjustment ring, a black
coloured inner part and a M3 stainless steel bolt. Before the adjustable end cap assembly is pressed onto the
axle, the two adjustable black and bronze coloured end cap parts must be assembled flush (anti-clockwise)
so that the end cap width is at its minimum.
TIP: When servicing the hubs, take special care to take note of the how the individual components are
assembled. In case you are not familiar with servicing hubs, please take the wheels to an experienced wheel-
builder or a Syntace service centre.
Adjusting axial play
The axial play is adjusted with the end cap.
Note: never adjust the axial play of the hubs when out of the bike, or else the bearings could be
damaged when first mounting the wheels in the bike!
Only proceed with adjusting the bearing play once the hub/wheel is in the bike and skewer or through axle is
tightened to manufacturer’s specifications. Proceed as follows:
•
loosen the clamping bolt of the end cap with a 2.5mm Allen
key
•
turn the black adjustment ring of the end cap anti-clockwise,
until it stops
•
the axle can now be moved from side to side in the hub body
by a couple of millimetres
•
before you put the hub into frame or fork, hold the hub body
and press the opposing end cap firmly towards the hub body
so that the small amount of freeplay can be felt the end of
the adjustable end cap
•
now place wheel in frame or fork and tighten skewer or
through axle to manufacturer’s specifications
•
now turn the adjustment end cap clockwise until you can feel
a slight resistance.
TIP: Now wind the adjustment end cap back by a small amount. Now tighten the clamping bolt to 0.5Nm. If
you don’t have a torque tool at hand, you can also use the short end of your Allen key with two finger tips,
and it will be very close to the recommended torque.
8
Changing the end caps
If you need to change the endcaps for another axle standard, proceed as follows:
•
Use a long piece of wood or plastic rod (as can be purchased at any hardware store), pass it through the
inside of the axle and knock off the end cap on the other side. Now enter the axle from the other side to
knock off the second end cap.
TIP: As the axle is free to slide through the hub, it is possible that this happens instead of the first end cap
coming off. If this happens, you will need to knock the end cap off the axle after removing it from the hub.
Then insert the axle back through the hub.
Maintenance, care and safety
Correct fitting, maintenance and care guarantees a long lifespan, durability and dependable function of your
Syntace components.
Follow these simple steps to service your wheels:
•
Do not clean the hubs with a high pressure water stream such as with a high pressure cleaner! When
cleaning the hubs with a high pressure water stream, water and dirt can enter the bearings. This will quickly
result in damaged bearings and will require replacing them.
•
A video of how to service the hubs can be found on the Syntace website: Syntace.com > support
•
Under normal conditions, remove the freewheel body twice yearly, clean and lubricate. Under frequent use
this may be neccesary at shorter intervals.
•
When taking the hub apart, clean thoughroughly and check all components for wear.
•
The springs are housed inside conical holes in the outer spur gear. To remove the springs, gently turn them
in a anti-clockwise direction.
Feder gegen den
Uhrzeigersinn
drehen!
When assembling the hub, carefully press the springs into the hub while turning them in an anti clockwise
direction. Only like this, the springs will be safely secured in the spur gear.
When lubricating the spur gears, do not use thick greases or copper paste! Lubricate the spur gears only
lightly with a motor oil (approx. 5 drops) or dip into an oil bath. Also lubricate the freewheelbody seal with
motor oil.
9
Before re-assembling the hub, check the bearings feel smooth. In case any bearing require replacing, fol-
lowing bearing kits are available:
Item No: 115385 Bearing Kit Front 15 28 hole
Item No: 115392 Bearing Kit Front 20 32 hole
Item No: 115378 Bearing Kit Rear
In order to have the bearings replaced, please see your wheel builder or Liteville Werksstation. Werksstations
have special tooling for changing the bearings.
Warranty
Instead of the legally required 2 year warranty, Syntace gives 10 years warranty from date of
purchase on all material and manufacturing defects.
Only condition: All components are to be installed and used as outlined in the owner’s
manual.
Syntace 3+7 wheels warranty:
Repair or replacement of the wheel or wheel part is free of charge in the first 3 years, after that and up until
the 10th year, a 50% usage fee will be charged relative to the current respective RRP.
The warranty does not apply to wearing parts or impacts to the rim etc. Further information to the process can
be found on: www.syntace.com/warranty_handling
Please take note: binding is always the most current owner’s manual as can be found on Syntace.de/support
Your Syntace Team
Jo Klieber
--------------------------------------------------------------------------------------------------
Register your product online: www.syntace.com/warranty
--------------------------------------------------------------------------------------------------
10
Hi
Tor
que MX R
ear 1
2 / R
ear 1
2 W
ide
Hi
Tor
que MX F
ront 1
5
Hi
Tor
que MX F
ront 20
Syntace Bearing
Kit Front 15 28
Hole
(2
pcs. 17x26x5mm)
(#115385)
Syntace
Bearing
Kit
Front
20
32
Hole
(2
pcs. 25x37x7mm)
(#115392)
Syntace HiT
orque
Cap Front 20
(pcs.) through a
xle 15x100
(#116689)
Syntace HiT
orque
Cap Front 20
adjustable
outside (#116665)
Syntace
HiT
orque
Ca
p
Front
20
adjusta
ble
20x110 inside
(#116634)
Syntace HiT
orque
Cap Front 20
adjustable
15x100 inside
(#116627)
Syntace hub bearing (1 pcs)
17x30x7mm rear hub body (#111769)
Syntace
hub bea
ring (1 pcs)
17x26x5mm
rea
r hub (#114562)
Syntace
Bea
ring
Kit
Rear
(4
pcs.)
#115378
2x Bea
ring 17x26x5mm (#114562)
2x Bea
ring
17x30x7mm (#111769)
HiT
orque
M+MX
freewheel
body
(#110656)
Inla
y f
or
freewheel
body
(#116481)
HiT
orque
Rear
Spring
(#111899)
HiT
orque rear
distance
tube
(#111806)
Crown
gear
ratched
Kit
(incl. ICL
4
springs)
(#115408)
HiT
orque f
reewheel sea
l NB
R 70/bla
ck
(#110496)
Syntace
HiT
orque
Cap R
ea
r 12
(pcs.) through
axle 12x142/157(#116702)
Syntace HiT
orque Cap Front 20
(pcs.) through axle 20x110 (#116672)
Syntace HiT
orque Cap R
ear12 adjustable set 12x142/157 (#116
658)
Syntace HiT
orque Cap Front 15 adjustable set 15x100 (#116641)
Syntace HiT
orque Cap Front 15
(pcs.) through axle 15x100 (#116696)
HiTorque MX Rear 12 / Rear 12 Wide
HiTorque MX Front 15
HiTorque MX Front 20
Syntace Bearing Kit Front 15 28 Hole
(2 pcs. 17x26x5mm)
(#115385)
Syntace Bearing Kit Front 20 32 Hole
(2 pcs. 25x37x7mm)
(#115392)
Syntace HiTorque Cap Front 20
(pcs.) through axle 15x100
(#116689)
Syntace HiTorque Cap Front 20
adjustable outside (#116665)
Syntace HiTorque Cap Front 20 adjustable
20x110 inside (#116634)
Syntace HiTorque Cap Front 20 adjustable
15x100 inside (#116627)
Syntace hub bearing (1 pcs)
17x30x7mm rear hub body (#111769)
Syntace hub bearing (1 pcs)
17x26x5mm rear hub (#114562)
Syntace Bearing Kit Rear (4 pcs.) #115378
2x Bearing 17x26x5mm (#114562)
2x Bearing 17x30x7mm (#111769)
HiTorque M+MX freewheel body
(#110656)
Inlay for freewheel body (#116481)
HiTorque Rear Spring
(#111899)
HiTorque rear distance tube
(#111806)
Crown gear ratched Kit
(incl. ICL 4 springs) (#115408)
HiTorque freewheel seal NBR 70/black (#110496)
Syntace HiTorque Cap Rear 12
(pcs.) through axle 12x142/157(#116702)
Syntace HiTorque Cap Front 20
(pcs.) through axle 20x110 (#116672)
Syntace HiTorque Cap Rear12 adjustable set 12x142/157 (#116658)
Syntace HiTorque Cap Front 15 adjustable set 15x100 (#116641)
Syntace HiTorque Cap Front 15
(pcs.) through axle 15x100 (#116696)
11
HiTorque MX Rear 12 / Rear 12 Wide
HiTorque MX Front 15
HiTorque MX Front 20
Syntace Bearing Kit Front 15 28 Hole
(2 pcs. 17x26x5mm)
(#115385)
Syntace Bearing Kit Front 20 32 Hole
(2 pcs. 25x37x7mm)
(#115392)
Syntace HiTorque Cap Front 20
(pcs.) through axle 15x100
(#116689)
Syntace HiTorque Cap Front 20
adjustable outside (#116665)
Syntace HiTorque Cap Front 20 adjustable
20x110 inside (#116634)
Syntace HiTorque Cap Front 20 adjustable
15x100 inside (#116627)
Syntace hub bearing (1 pcs)
17x30x7mm rear hub body (#111769)
Syntace hub bearing (1 pcs)
17x26x5mm rear hub (#114562)
Syntace Bearing Kit Rear (4 pcs.) #115378
2x Bearing 17x26x5mm (#114562)
2x Bearing 17x30x7mm (#111769)
HiTorque M+MX freewheel body
(#110656)
Inlay for freewheel body (#116481)
HiTorque Rear Spring
(#111899)
HiTorque rear distance tube
(#111806)
Crown gear ratched Kit
(incl. ICL 4 springs) (#115408)
HiTorque freewheel seal NBR 70/black (#110496)
Syntace HiTorque Cap Rear 12
(pcs.) through axle 12x142/157(#116702)
Syntace HiTorque Cap Front 20
(pcs.) through axle 20x110 (#116672)
Syntace HiTorque Cap Rear12 adjustable set 12x142/157 (#116658)
Syntace HiTorque Cap Front 15 adjustable set 15x100 (#116641)
Syntace HiTorque Cap Front 15
(pcs.) through axle 15x100 (#116696)
HiTorque MX Rear 12 / Rear 12 Wide
HiTorque MX Front 15
HiTorque MX Front 20
Syntace Bearing Kit Front 15 28 Hole
(2 pcs. 17x26x5mm)
(#115385)
Syntace Bearing Kit Front 20 32 Hole
(2 pcs. 25x37x7mm)
(#115392)
Syntace HiTorque Cap Front 20
(pcs.) through axle 15x100
(#116689)
Syntace HiTorque Cap Front 20
adjustable outside (#116665)
Syntace HiTorque Cap Front 20 adjustable
20x110 inside (#116634)
Syntace HiTorque Cap Front 20 adjustable
15x100 inside (#116627)
Syntace hub bearing (1 pcs)
17x30x7mm rear hub body (#111769)
Syntace hub bearing (1 pcs)
17x26x5mm rear hub (#114562)
Syntace Bearing Kit Rear (4 pcs.) #115378
2x Bearing 17x26x5mm (#114562)
2x Bearing 17x30x7mm (#111769)
HiTorque M+MX freewheel body
(#110656)
Inlay for freewheel body (#116481)
HiTorque Rear Spring
(#111899)
HiTorque rear distance tube
(#111806)
Crown gear ratched Kit
(incl. ICL 4 springs) (#115408)
HiTorque freewheel seal NBR 70/black (#110496)
Syntace HiTorque Cap Rear 12
(pcs.) through axle 12x142/157(#116702)
Syntace HiTorque Cap Front 20
(pcs.) through axle 20x110 (#116672)
Syntace HiTorque Cap Rear12 adjustable set 12x142/157 (#116658)
Syntace HiTorque Cap Front 15 adjustable set 15x100 (#116641)
Syntace HiTorque Cap Front 15
(pcs.) through axle 15x100 (#116696)
12
Please look for the newest updates of this manual at:
Syntace.com > Support
Syntace GmbH
Dammweg 1 D - 83342 Tacherting
Tel. +49 (0)8634 66666 Fax +49 (0)8634 6365 syntace@syntace.de
Current: 04.04.2014