SYSFORM FP-10H Operating Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

Content

Part one: Notes

Manual Range………………………………………………2

Safety Requirements……………………………………… 2

Part Two: Symbols

……………………………………4

Part Three: Quick Start

Introduction………………………………………………4

Product Appearance………………………………………5

Opening the package……………………………………….5

Connect the power and insert SD card……………………6

Part

Four

Operation Instructions

Button ……………………………………………………7

Foil Transmission ………………………………………8

Foil Installation …………………………………………9

Start………………………………………………………9

Printer settings………………………………………….10

Print head maintenance…………………………………17

Part Five : Technical Parameters

………………….18

Note : Design the printed words or pictures using CorelDraw, AI or

Photoshop …etc…any software in computer and save in SD card

with BMP format (file name should be numerical character or

English character) then insert foil printer for printing.

For FP-20H & FP-30H if you want to connect computer you need a

driver that saved in SD card. When work in-line you don’t need to

save file, just print directly.

The max. width of file for 10H & 20H is 57mm but 30H is 300mm

Warning: Don’t put your fingers under the printing head when

machine is operating.

Part One

：

Notes

1, Un-pack:

Remove the four screws marked (tighten between main body

and working platform) when the machine is ready for printing.

2. Manual range:

To ensure the user use the foil printer correctly and efficiently,

please make sure read all the content of the manual, please keep the

manual at the proper place for reference anytime. Before operation,

please read the basic system, warnings, notes and tips.

3. Safety requirements:

Please observe all the warnings and notes on the printer to avoid any

personal injury and printer damage, we warn the operator by tip.

Note: warn the operator that the system may be damaged if not

operate correctly

Warning: warn the operator that personal injury may be caused if

not operate correctly.

A. Notes: only qualified and trained person can repair the printer;

B. The electronic components on the control board are very sensitive

to the static electricity

, easy to damage;

C. The internal voltage has the risk of electric shock.

D. Both hands and clothes should be hold off to the moving parts to

ensure the safety

Forbidden touching the print head after the printer has just

stopped or the printer on operation;

F. Please pull the plug to cut off the power supply, rather than pull

the power cable

G. When change electric parts, please use the parts that with same

specification and capacity only print-matching and grounding power

cable can be used;

H. Forbidden putting any items on the printer, the printer should be

hold off any liquid and pollutants.

I. The printer can produce radio frequency on operation, harmful

Interference may be caused if not used and installed correctly ,

the user need to eliminate the interference when using at the

housing residences.

Part Two: Symbols

ON : press down the symbol on the switch , the power is

on.

OFF: press down the symbol on the switch , the power is off

Part Three: Quick Start

1. Function introduction

Digital foil printer is a mini table foil printer, can foil print in gold

and silver ,no need to make dies or plates, artworks designed on the

computer, can print once the design finished, it is very time-saving;

Special software control, eliminate the problem of printing complex

artworks; Print medium including copper plate paper, mount paper,

adhesive paper, designed, fabric, ribbons. The applied projects are

diary book covers, advertising professional project, and some other

new projects. etc. This printer can help to save much time of setting,

and also eliminate the mould, mesh, printing ink and solvent that

used in the traditional printing, greatly reduce the direct and indirect

printing costs. This printer may produce radio interference if used in

(3) SD card and card reader( demo video and some demo files saved

in SD card )

(4) Demo Foil

(5) Operating manual

【

note 1

】

: the packaging size is 67 cm * 67 cm * 54 cm, please

place it properly so that the operator has move access

【

note 2

】

: place the printer on the flat item that at least can

burden twice weight of the printer

【

note 3

】

: if the printer raised improperly , it should cause badly

damage, forbidden raising the printer by holding the upper cabinet

and the parts, please make sure to hold the printer bottom to raise

【

note 4

】

: please do not touch the print head direct by hands.

【

note 5

】

: please keep up the packaging case and packaging

materials properly for future moving and maintenance

4. Connect the power and insert SD card

【

note 1

】

: the printer power cable must match the rated power,

please check the power if proper by using different power

【

note 2

】

: check the switch if is on the OFF position. The

symbol "O" means power off

The power cable plug should be firmly inserted into the printer

power interface

The other end of the power cable should be insert a plug with

grounding

3. Insert the SD card.

Part Four : Operation instruction

【

note 1

】

:Anyone who is unqualified and untrained should not

open the electric component cabinet.

1.Buttons

Reset

When the printer is on the printing condition, the platform and

the print head Reset, and cancel the printing task, so when

the printer is on printing condition, please use this button carefully ;

When the printer is out of the printing condition press down this

button, the print head and platform will reset.

↑

means page up

MENU means the job list .

SELECT means the job list can be selected

←

means page left.

↓

means page down.

→

means page right

PAUSE means PAUSE.

2. Foil transmission

Supply-side

used to install the unused foil ribbons.

Recycling-side

to receive the used foil ribbon, and also provide the

proper tensile force to avoid the foil ribbon folded.

Guiding

Shaft

Used to transmit the foil ribbon,to prevent the foil

from folding.

Print Head

Used for heating and printing

Work platform

To place print medium

【

note 2

】

: the print head may be permanently damaged by the

badly mechanical impact and static charge, for more details please

refer to the "print head maintenance" in chapter 4

Before printing, please make sure read all the content in this chapter

3. Foil Installation

【

note 1

】

: please don't place the foil upside down (please refer

to the installation below), please don't print without the foil ribbon

installed

【

note 2

】

: please use the qualified thin film, foils or color

ribbon, the damage that caused by using unproper materials will be

out of warranty, and the fix fee will be at users own expense

4. Start

Please check to ensure all the below steps are finished before

printing

(1)

SD card inserted (check to see if the SD card with the printing

job list).

(2) already loaded foil ribbon.

(3) printer is on power.

(4) the printing medium is on the platform

(5)

the printer need to hold off the items around to prevent the

impact when the platform moving during printing

5. Printer Setting

printer setting need to the follow below steps:

Tip: No need to set the printer every time, all the parameters will be

saved automatically after the initial setting, users only need to

change the parameters if use different material and different foils.

After turning on, the screen will display as below:

Press

and the screen display as below

Standy

File management

Setting

Language

Service

Quit

(1) Settings

A. Press

and came to the setting

B. Press

and the screen display as blow

File management

Setting

Language

Service

Quit

Setting

Print settings

System

Quit

C. Press

to select the print setting and the screen display as

below

①

Select the SPEED to adjust the printing speed, for the operation

please refer to the remarks

②

Select the PRESSURE to adjust the pressure of the print head,

for the operation please refer to the remarks

③

Select the DARKNESS to adjust the heat of the head, for the

operation please refer to the remarks

Print Settings

Speed

Pressure

Darkness

Quit

Remarks:

symbolize increase

symbolize

reduce

Note:

①

The speed range is: 1 ~ 3, normal using 3

②

The pressure range: 0 ~ 80, normal using 20

③

Printing darkness range: 1 ~ 18, normal using 3

Above settings are used usually, but different printed materials

should be different settings and different foil used. It Depends on

user’s experience.

(2) Select file

Tip: the user can select the files in SD card to start the printing.

A. Press

and come to the File Management as below

B. Press

and come to the File list as below

C. Select File list, and then you will see the file listed in orders

now you can select the wanted file, and press

start printing.

(4) Language selection

File management

Setting

Language

Service

Quit

File management

File list

Quit

A. Press

and come to the Language

B. Press

and the screen display as below.

C. Select Simplified Chinese or English

。

6.Print head maintenance

File management

Setting

Language

Service

Quit

Language

Simplified Chinese

English

Quit

The print head may be attached by the dust, foils, carbon, etc, this

may cause the bad printing (i.e. parts can't print). So the user need

to ensure the printing consumables attached by the dust or some

other dirt things, by doing this can help to increase the printing life

of the head. And user can clean the print head as below steps:

1. Turn off the power

2. Take off the foil

3. If the head attached by dirty things, please clean it with alcohol

pen or soft cloth with alcohol

4. After the surface clean, user can use dry cotton swabs to remove

the left alcohol to make it dry quickly

【

notes 1

】

1. Please clean the print head every week.

2. Please don't touch the heating parts with hands.

3. If can guarantee the print quality, try to minimize printing

pressure.

【

note 2

】

when clean the print head please make sure the soft cloth are not

attached with metal or hard things, if the head damaged by the dirty

cloth, this will be out of warranty.

Part Five: Technical Parameters

Model

FP-10H / FP-20H/FP-30H

Printing interface

SD card

SD card & USB

Max printing length

250mm

Max printing width

57mm 300mm

Max thickness admits

50mm 30mm

Max feeding width

350mm

Speed

20-50mm/s

Operation System

Win XP / Win 2000 / Windows 7 32 bit

Resolution

300 dpi

Power

150W

Power source specification

110V/240V 50/60HZ 150W max

Machine size

68cm*51cm*29 cm

Packaging size

67cm*67cm*54cm

GW/N.W

36KG/24KG

Medium types

Paper, PVC , leather, photo

paper ,cardboard, ,plastic. rubber ,film, vinyl,

PET ,etc

PDF User Manual

FP-20H FP-30H

Full Text Searchable PDF User Manual