Full Text Searchable PDF User Manual
Automatic switching or dimming when used in combination
with 1-10V dimmable LED drivers or ballasts.
Built-in daylight sensor.
1-10V interface can match up with Merrytek stand-alone
daylight sensor MS01 and achieve daylight harvesting.
Compact size makes it suitable to fix within most luminaires.
Detection area, time delay and daylight threshold can be
precisely set via DIP switch.
Wide detection area, range up to 16m in diameter.
Support higher mounting height 15m Max.
Optional surface mounting and base mounting
Introduction
The MC601V innovative and active motion detectors with
HF system 5.8GHz. Motion can be detected through
plastic, glass and thin non-metal materials.
The sensors allow energy saving without compromising
comfort. When used in combination with 1-10V dimmable
LED drivers or ballasts, they can achieve 3-step dimming
function, which is perfect for use in some areas that
requires a light change notice before totally switch off.
Also, the 1-10V interface in the sensors can match up with
M e r r y t e k s t a n d - a l o n e d a y l i g h t s e n s o r M S 0 1 , a n d
implement daylight harvesting, means the lighting system
has automated controls that either turn off or dim artificial
light in response to the available daylight in the space.
As it uses the third generation Merrytek technology, normal
5.8GHz microwave module can easily reach high mounting
high up to 15m and long detection area 10m in radius.
Light Sensor
Max.8M
Hold Time
10s~30min
15m
Mounting Height
15 m Max.
Automatic
Dimming
10
%
50
%
5 Years
Guarantee
5
5
Years
Guarantee
SYNC
Cluster-control
Version
MC601V
North America Version / Dimming Function
C
US
Dim
mi
ng
Wiring scheme
Lamps in corridor are controlled by several sensors. Once any motion is detected by one of sensors, the motion
signal will be transmitted to other sensors connected together. Then, all lamps switch on at the same time, instead
of switching on the lamps in the area where motion is detected.
Dimming Function
3-step dimming function
No motion detected,
all lamps switch off.
1
Any movement is detected
from any direction, all lamps
synchronously switch on.
2
No motion is detected in
detection area, all lamps
synchronously dim to a low
light level after hold time.
3
After stand-by period, the
lamps switch off if no
movement is detected in
the detection zone.
4
3
6
6
12
3
sensor
slave
slave
slave
sensor
sensor
2
sensor
slave
slave
slave
sensor
sensor
1
sensor
slave
slave
slave
sensor
sensor
4
sensor
slave
slave
slave
sensor
sensor
Wiring scheme
ON -OFF Function
Motion sensor MC601V + LED driver or ballast (Any brand)
MC601V is an innovative motion sensor, switch on the light on detection of movement, and switch off after a hold
time when there is no motion detected. As built-in daylight sensor can read brightness value, the sensor does not
switch on the light if with sufficient natural light.
With sufficient light, the lamp
doesn't switch on.
After hold time, the sensor
switches off the lamp when
no motion is detected.
1
2
3
With insufficient ambient light,
the sensor switches on the lamp
when motion is detected.
Daylight Harvesting
When used in combination with Merrytek daylight sensor MS01, the system has automated controls that either
turn off or dim artificial light in response to the available daylight in the space.
Ambient light below than
preset illumination level,
the lamp switches on
when motion is detected.
Ambient light larger than
preset illumination level
(Set by 1-10V daylight
sensor), the lamp keeps
off.
The lamp lights on 100% illumination or dims to maintain the preset illumination
level against the level of ambient light.
L
N
Control gear
Max. 400W
L
N
Control gear
L
N
Control gear
Wiring scheme
If with sufficient ambient
light, the lamp turns off
at once,even with motion
trigger.
If with insufficient ambient light, the lamp dims to stand-by dimming level (Set in the motion
sensor) when no motion detected ofter hold time, and then switches off after stand-by period.
3
6
6
12
Detection Pattern
Ceiling mounting pattern (Unit: m)
Suggested installation height: 2.5-10m
Wall mounting pattern (Unit: m)
Suggested installation height: 1-1.8m
10%
25%
50%
75%
100%
0
2
4
8
6
2
4
6
8
10
12
14
10
12
14
10
12
14
16
16
16
18
18
18
10%
50%
75%
100%
Detection area
Detection area can be reduced by selecting the combination on the
DIP switches to fit precisely each application .
MC601V
Setting
Hold time
Refers to the time period the lamp remains at 100% illumination after no
motion detected.
Stand-by period
Refers to the time period the lamp remains at a low light level before it
completely switches off in the long absence of people.
When set to“ ”mode, the low light is maintained until motion is detected.
Stand-by dimming level
The low light level you would like to have after the hold time in the long
absence of people.
Daylight sensor
The sensor can be set to only allow the lamp to illuminate below a defined
ambient brightness threshold.
When set to Disable mode, the daylight sensor will switch on the lamp when
motion is detected regardless of ambient light level.
50lux, 30lux: twilight operation, 10lux, 5lux: darkness operation only.
Note that daylight sensor is active only when lamp totally switches off.
By selecting the combination on the DIP switches, sensor data can be precisely set for each specific application.
ON
ON
ON
Operating voltage 120~277Vac, 50Hz/60Hz
Rated capacitive load 120V@400W;220-240V@800W;277V@1000W
HF system 5.8GHz±75MHz, ISM wave band
Transmitting power <0.5mW
Power consumption
≤
0.5W(standby), <1W(operation)
Detection zone Max.(D x H): 16m x 15m
Detection sensitivity 10% / 50% / 75% / 100%
Hold time 5s / 30s / 90s / 3min / 20min / +
Daylight sensor 2lux/5lux / 10lux / 25lux /50lux / 100lux / Disable
Stand-by period 0s /5s / 5min / 10min / 30min / 1h / +
Stand-by dimming level 10% / 20% / 30% / 50%
Mounting height 15m Max.
Motion detection 0.5~3m/s
Detection angle
150°(wall installation),
360°(ceiling installation)
Operating temperature -35
℃
~70
℃
IP rating IP20
ON
8
8