Full Text Searchable PDF User Manual
Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 1
BLE 5.0 & WiFi Gateway Specification
BLE WiFi Gateway
Model: G1
Version: V1.3.2
Contents
Contents ...................................................................................................................................... 1
1.Overview ................................................................................................................................... 2
2.Features .................................................................................................................................... 3
3.Typical Application .................................................................................................................... 3
4.Outside View ............................................................................................................................ 4
5.Electronic Parameters ............................................................................................................... 5
Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 2
BLE 5.0 & WiFi Gateway Specification
1. Overview
G1 is a Bluetooth 5.0 low energy (BLE) to Wi-Fi connectivity gateway without the uses of smartphones or
apps. The G1 gateway collects the data from iBeacon, Eddystone, BLE sensor and other BLE devices, and
then sends to the local server or remote cloud server by HTTPs / MQTT/mbed (ARM) protocol with SSL
and TLS certification over Wi-Fi / Ethernet / Cellular. The subsequent version G1 Gateway will also
implement the connection with BLE devices. This product is a science fiction with a color lamp ring on
the top. It can be fixed by sticker or screw thread.
Outside View
Internal Structure
Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 3
BLE 5.0 & WiFi Gateway Specification
2. Features
General:
●
1A @ DC 5.0V input, micro-USB
●
10/100 Ethernet, POE (802.3af)
●
Firmware upgrade OTA
●
Multiple data transportation protocols
Local server: TCP / UDP
Remote serer / Cloud: HTTP/MQTT/mbed(ARM) with SSL and TLS certification
●
Operating temperature: -15
℃
to 55
℃
WIFI:
●
Wifi module based on the Mediatek MT7628 580MHz 32-bit Application Processor
●
2T2R 2.4 GHz with 300 Mbps PHY data rate,802.11b/g/n WiFi
●
Two USB 2.0 Host Connectors and one TF Card slot
●
128M bytes 16-bit DDR2 RAM
●
16M bytes SPI NOR Flash
●
RGB LED strip as the status indicator
●
OpenWrt 15.05, Linux distribution for embedded devices.
BLE:
●
BLE module based on the Nordic's nRF52832 with ARM
®
Cortex
®
-M4 64MHz 32-bit processor
●
At least Bluetooth 4.0(Only Bluethooth Low Energy)
3. Typical Application
●
iBeacon / Eddystone / other BLE tag receiver
●
BLE sensor reader / receiver
●
Asset tracking
●
Access control management
●
Advertisement promotion
●
Indoor location and position
●
Industrial automation
Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 4
BLE 5.0 & WiFi Gateway Specification
S1: Bluetooth temperature & humidity sensor E2: 300 to 500 meters MaxBeacon
E6: Bluetooth ambient light sensor i3: Waterproof iBeacon & Eddystone
i7 : Bluetooth accelerometer sensor C7: Credit card beacon with RFID/NFC
G1: Bluetooth & WiFi gateway
4. Appearance
G1-C
Sign & Slots
Feature Description
ON/OFF
Power On / Off device
Reset
Factory reset or close/open AP
RJ-45
10/100Mbps Ethernet, 802.3af PoE
USB
2pcs external USB2.0 slot
IN
Micro-USB, power input (5.0V DC, 1A)
TF
TF card slot (reverse)
Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 5
BLE 5.0 & WiFi Gateway Specification
The meaning of the top LED Strip Lights status is as follows:
Static LED Strip Lights
Indicates that the gateway is staring
Dynamic white light rotation
Indicates that the gateway has been started
Dynamic LED Strip Lights
rotation
Indicates that the gateway is not connected to the server
Dynamic breathing lights
Indicates that the gateway is already connected to the server
(Note: The gateway is in the dynamic breathing lights by
default, it can step into the energy-saving mode on minute
after extinction of lights, you also can set up bright mode in
the configuration page if rich enough)
LED Strip Lights go out
Indicates that the gateway is not power or in energy-saving
mode
5. Electronic Parameters
General Information
Color
White
Size
150x150x36mm
Net Weight
180g
Accessory
1x USB cable, mental fixing and screws
Absolute Maximum Rating
Power supply (Vcc)
Max. 5.5 Volts, DC
Storage temperature
-40
℃
to 85
℃
Voltage ripple
+/- 2%
Operation Condition (Recommendable)
Operating temperature
-15
℃
to 55
℃
Humidity
Max 95%, Non condensing, relative humidity
Power supply (Vcc)
DC 5.0 (+/- 5%)
Current Consumption
Powered by Micro-USB
330mA (LED strip and Wi-Fi works in the same time)
290mA (Wi-Fi only)
Powered by PoE
340mA (LED strip and Wi-Fi works in the same time)
300mA (Wi-Fi only
Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 6
BLE 5.0 & WiFi Gateway Specification
Wi-Fi RF Performance
Wireless
IEEE 802.11b/g/n (single stream)
Network modes
Router, Repeater, Cellular (coming soon, Q4/2017)
Data rate
IEEE 802.11b, 1-11Mbps
IEEE 802.11g, 6-54Mbps
IEEE 802.11n(2.4GHz),
150
Mbps
Frequency band
2.4
12
–
2.4
62
GHz
Number of selectable Sub
channels
1
1
channels
Channel Bandwidth
20 / 40 MHz
Modulation
OFDM, DSSS, DBPSK,DQPSK, CCK , 16 / 64QAM
Maximum receive input level
- 10dBm (with PER < 8%@11 Mbps)
- 20dBm (with PER < 10%@54 Mbps)
- 20dBm (with PER < 10%@MCS7)
Minimum receive input level
- 87dBm (typ. with PER < 8%@11 Mbps)
- 70dBm (typ. with PER < 10%@54 Mbps)
- 70dBm (typ. with PER < 10%@MCS7)
Transmit Power
1
8.13
dBm (typical)@ 802.11b
1
7
.3
6
dBm (typical)@ 802.11g
18.8
dBm (typical)@ 802.11n
Carrier Frequency Accuracy
+/- 20ppm (crystal: 16MHz +/-10ppm in 25
℃
)
Antenna
FPC antenna
Range
up to 100 meters( in open space)
Security
WPA / WPA2
BLE RF Performance
Operation Mode
LAN mode
Transmission Power
Ranges from -30 to +4dBm
RF Power Accuracy
+/- 4 dB
Receiver Sensibility
-108 dBm @250kbps, 0.1% BER
-93 dBm @1Mbps, 0.1 %BER
Maximum Received Signal
Strength at <0.1% PER
0dBm
Frequency Deviation
+/-250 kHz @BLE
Antenna
Flexible FPC antenna
Scanning & concurrently
process
200 BLE devices per second
Range
300 meters in open space (max.)
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be
installed and operated with minimum distance between 20cm the radiator your body: Use
only the supplied antenna.