Full Text Searchable PDF User Manual
FG-602 SVGL
FG-603 SVSS
FG-633 SVSS
FG-3773 SVGL
FG-3793 SVSS FG-772 SVGL FG-773 SVGL
B U I LT-I N H O B
FG-602 SVSS
FG-772 SVSS
FG-2792 SVGL
FG-3773 SVSS
FG-603 SVG
L
FG-622 SVSS
FG-2792 SVSS
FG-3793 SVGL
1
2
The cooker may be troubled if
disassembled or modified.When
the cooker is in trouble,contact
your dealer.
A fire or a carbon monoxide
toxication may be caused by
the lack of air supply.
In the event of abnormal condition (abnormal
combustion,sell and soud, earthquake and
fire) make sure to stop the operation and
close the gas main valve.
3
!
Caution
If it is poorly ventilated,a carbon
monoxide toxication may be caused by an
incomplete combustion.
If they are closed, the cooker may
be overheated and cause a fire or
a carbon monoxide toxication.
An explosion or a fire may be
caused.You will get burnt.
■
Strictly followed operating instructions for
installation.Installation carried by
unlicensed installer can cause
fire and appliance breakdown.
!
Caution
!
If a gas hose get old,it will become
loose and be cracked. Then, gas
leaks may be caused.
Please regularly check the flame or complete
combustion. If abnormal noise and
unstable flame is found, please do
not attempt to use. Otherwise it will
result in CO poisoning.
There may be a case that you will
get burnt or your hair will get burnt
by its heat or flame.
■
Make sure to confirm that the burner flame is
extinguished after use. Make sure to close a
gas main valve before going out or going to
bed.
■
If the cooker is used for other purpose like
drying clothes,it may be overheated or may
cause an abnormal operation.Then, a fire,
burning or a gas leak may be caused.
If the oversized cooking utensils are used,
a carbon monoxide may be caused by the
abnormal combustion of the cooker.
2
(The area of the air inlet is to be 10cm for
every 1.2kW heat input, The air inlet
2
required for this appliance is 60cm )
If there is insufficient air supplied to the
appliance,it would cause incomplete
combustion and thus CO poisoning.
A top plate,trivets and exhaust port and their
vicinity become extremely hot and there may
be a case that you will get burnt.
The grips of pan will be overheated
by the overflowing flame. And you
will get burnt or a fire may be
caused.
do not
touch
4
The drop objects would cause fire and the
plastic lighting facilities would result of
serious distortion under high heat from the
appliance.
Humid environment would cause the faults
to the appliance parts and shorten the
product life.
If the appliance is not firmly placed in level.
It may cause incomplete combustion and
thus generate excessive CO and fire.
It would cause fire and unnecessary faults
to the appliance while under serious
vibration.
It is illegal to employ disqualified installer
to carry out the installation and it may
result in gas leaks.
The recommended air inlet size is about
3cm x 20cm.
It is recommended to put the metal mesh
on the air inlet to prevent rat from entering.
If the air supply to the appliance is not
sufficient, it would cause incomplete
combustion and thus excessive CO
generated.
5
Utensils should always be placed centrally on the pan supports over the burners.
Flames which extend beyond the bottom of utensils are wasteful and can damage
or overheat handles.Large diameter utensils (greater than 200mm in diameter)must
not be allowed to protrude beyond the perimeter of the hotplate,as this could cause
overheating or damage to the adjacent bench.
Do not place anything,e.g.flame tamer,asbestos mat,between pan
and pan support as serious damage to the appliance may result.
Do not remove the pan support and enclose the bumer with a wok
stand as this will concentrate the flame and deflect the heat onto the
gas hob.
Never use oversized cooking utensils or overload the cooking
appliances.
Locate pan centrally over burner so that it is stable and does not
overhang the appliance.
Do not damage the outer surface of the glass with heavy or
sharp objects.
Do not spray aerosols in the vicinity of this hotplate while in operation,Some
propellant gases can break down when heated and produce corrosive vapours
which will attack some materials.
Articles which are made from flammable materials should not be stored in
drawers of cup boards immediately below this hotplate.
Do not store articles within 50mm of the bottom of the hotplate casing.
Do not touch spark ignitor while lighting the burner.
6
Glass Top Plate :
Cut-Out Size :
750 x 500 x 8(mm)
(A) 540 x (B) 350 x R60(mm)
Glass Top Plate :
Cut-Out Size :
880 x 510 x 8(mm)
(A) 785 x (B) 425 x R60(mm)
6
4
5
3
1
2
8
10
FG-622 SVSS
FG-773 SVGL
FG-633 SVSS
5
3
1
2
10
I ron G r id(I ar ge)
Ultr a-r apid bur ner
C ontrol knob for bur ner (R ight)
C ontrol knob for bur ner (C enter )
C ontrol knob for bur ner (L eft)
Auxiliar y bur ner
7
8
9
10
11
Semi-r apid bur ner
I ron G r id(small)
I ron G r id(medium)
Top plate
C ontrol knob for bur ner (R ight back)
FG-602 SVGL FG-602 SVSS
FG-603 SVGL FG-603 SVSS
6
8
5
11
3
10
2
Stainless steel Top Plate: 865x505(mm)
Stainless steel Top Plate:
750x450(mm)
1
2
3
4
5
6
P arts identifc ation
5
3
1
2
10
Glass Top Plate :
Cut-Out Size :
880 x 520 x 8(mm)
(A) 705 x (B) 405 x R60(mm)
6
4
5
3
1
2
8
10
FG-3793 SVGL FG-3793 SVSS
FG-3773 SVGL FG-3773 SVSS
I ron G r id(I ar ge)
Ultr a-r apid bur ner
C ontrol knob for bur ner (R ight)
C ontrol knob for bur ner (C enter )
C ontrol knob for bur ner (L eft)
Auxiliar y bur ner
7
8
9
10
11
Semi-r apid bur ner
I ron G r id(small)
I ron G r id(medium)
Top plate
C ontrol knob for bur ner (R ight back)
FG-772 SVGL FG-772 SVSS FG-2792 SVSS FG-2792 SVGL
Stainless steel Top Plate: 865x505(mm)
6
8
9
7
1
2
10
5
11
3
1
2
3
4
5
6
Glass Top Plate :
Cut-Out Size :
780 x 460 x 8(mm)
(A) 650 x (B) 350 x R60(mm
Stainless steel Top Plate: 750x450(mm)
8
P arts identifc ation
5
3
1
2
10
9
FG-773 SVGL
FG-633 SVSS
3.8
3.8
1.4
2.0
3.8
3.8
9.0kW
9.6kW
FG-772 SVSS
FG-602 SVGL
FG-602 SVSS
FG-622 SVSS
FG-603 SVGL
FG-603 SVSS
3.8
3.6
1.4
2.0
1.4
2.0
6.6kW
7.6kW
Product
Model
Ignition
Type of Gas
Overall Dimension
Cut-out Size
FG-602 SVSS FG-603 SVSS
FG-602 SVGL FG-603 SVGL
750mm x 500mm
540~720mm x 350~470mm
FG-622 SVSS FG-633 SVSS
865mm x 505mm
785~840mm x 425~480mm
FG-773 SVGL
Left
●
R Front
●
R Back
750mm x 450mm
540~730mm x 350~430mm
880mm x 510mm
3.8
3.6
3.8
3.6
7.6kW
7.2kW
Product
Model
Specification
Ignition
Type of Gas
Overall Dimension
Cut-out Size
2 & 3 Burner Built-in Hob
FG-772 SVSS FG-2792 SVSS
Battery : Size D 1.5V
LP Gas / Town Gas
750mm x 450mm
650~740mm x 350~430mm
Product
Model
Ignition
Type of Gas
Overall Dimension
Cut-out Size
2 & 3 Burner Built-in Hob
Battery : Size D 1.5V
LP Gas / Town Gas
865mm x 505mm
705~840mm x 405~480mm
Diameters of pan which may be
use on the hobs
Min : 120mm
Max : 260mm
..
Use only flat bottom pan except for wok burner.
For pan diameter of 120mm use trivet provided.
FG-772 SVGL
FG-2792 SVSS
FG-2792 SVGL
L.P.Gas (30mbar)
Town Gas mbar
(
)
8
Gas consumption per hour respective
gas consumption
Right
3.8
Left
3.8
3.8
Gas consumption when all
burner are on
7.6kW
7.6kW
FG-3773 SVSS
FG-3773 SVGL
L.P.Gas (30 b
m ar)
(
a
Town Gas mb r)
8
Gas consumption per hour respective
gas consumption
Right
Centre
Left
3.8
3.8
1.4
2.0
3.8
3.8
Gas consumption when all
burner are on
9.0kW
9.6kW
1 0
L.P.Gas :Diameter 9.5mm gas specific rubber hose
Town Gas:1/2IN Thread(male)
Gas connecting tube
3.8
FG-2792 SVGL FG-772 SVGL
780mm x 460mm
FG-3773 SVSS FG-3793 SVSS FG-3773 SVGL FG-3793 SVGL
880mm x 520mm
L.P.Gas (30 b
m ar)
(
a
Town Gas mb r)
8
Gas consumption per hour respective
gas consumption
Left
R.Front
R.Back
3.8
3.8
2.8
3.3
1.4
1.7
Gas consumption when all
burner are on
8.0kW
8.8kW
FG-3793 SVSS
FG-3793 SVGL
11
Prior to installation, ensure that the local distribution conditions (nature of the gas and gas
pressure) and the adjustment conditions of the appliance are compatible.
These hobs are designed to be used by private individuals in their homes.
Since this appliance is not connected to a combustion products evacuation device, it must be
installed in accordance with current installation regulations and used in a well - ventilated
place,particular attention should be given to the relevant requirements regarding ventilation.
The hob must be built into the worktop as illustrated on the corresponding figure of a support
cupboard. This worktop must be at least 3 cm thick and heat - resistant or else coated with a
heat resistant material.
A distance of at least 5 cm from the appliance border to the wall and a sideclearance of at
least 15 cm should be left to the right and left of the hob.In case those units are above the
appliance, these must be placed at a minimum distance of 80 cm from the appliance top.
It is advisable that a horizontal partition is put under the hob,it must be placed between 10 to
15cm from the bottom of the worktop. In any case, do not keep any sprays or pressurized
containers in the compartment,which could be just under the hob.
A
A
Back w
all
FRO
NT
A
B
50mm
Cut-Out Dimension - Please refer Page 7 for selected model.
B
B
1 2
Burner cap may discolored,chrome plated burner head and enamelled decoration cover
will pearl - off/drop - off and rusty after the appliances are used,However there is no
trouble for operating the cooker.
1 3
Before using the Appliance for the first time
- Select the required burner by referring to the
symbols located near the knobs (e,g:for the
right-hand burner)
- Each burner is supplied by a tap.To turn this
on,press it down and turn it anti-clockwise
The gas is turned off.when the knob points to
：
To turn the gas down the knob should be tur-
ned from
“
”
to
“
”
.
- Your hob is equipped with a burner ignition
device integrated into the knobs:To ignite a burner.
Press down and turn the knob anti-clockwise untill
It is pointing to the maximum position
“
”
Keep the knob pressed down to activate a
series of sparks until the burner lights.
- Select the required burner by referring to the
symbols located near the knobs
- A tap equipped with a gas safety device
controls each burner and if the flame is
accidentally extinguished(spills, draughts etc...)
This device automatically closes down the gas
supply and prevents gas escaping.
- Your hob is equipped with a burner ignition
device integrated into the knobs.
- To ignite a burner. Press down and turn the
knob anti-clockwise until it is pointing to the
maximum position
“
”
- To turn the gas down the knob should be
turned from
“
”
to
“
”
When the flame appears keep the knob well
pressed down for a few seconds to activate
the safety device.
Release. If the flame is extinguished,repeat
the operation.
Follow the same procedure described above to ignite the burners. In this case, however, once you have
turned the knob to open setting,hold it pressed in for 10 seconds. If for any reason the burner
flame goes out, the safety valve automatically shuts off the gas supply to the burner in question.
In the even of the burner flames being accidentally extinguished,turn off the burner control and do not
attempt to re-ignite the burner for at least 1 minute.
The ignition device shall not be operated for more than 15 second.If after 15 second the burner has not
lit,stop operating the device and open the comartment door and / or wait at least I minute before
attempting a further ignition of the burner.
Placed the saucepan on the selected burner and activate.
If the flame is accidentally extinguished just re-light it normally following the ignition instructions.
Your hob is equipped with an integrated ignition device, It is,therefore,normal that a series of sparks is
produced on all the burners.
If it becomes difficult to tum a knob DO NOT FORCE IT.Have the Installer see to it immodiately.
In the case of a power cut,automatic lighting will not work,In these circumstances,matches may be used
1 4
Press the ignition knob and
turn it anti-clockwise to the
[ON] position as shown.
Then hold and wait for a few
seconds.
Release the knob and check
the flame if ignited. If the
flame can`t be lgnited, rum
the knob to [OFF] position
and repeat the above steps.
Note:
It would take longer time of
ignition if the appliance is not
being use for a long time or it is
a new installation.
Inner and outer
b u r n e r s a r e
at high flame
position
Inner and outer
b u r n e r s a r e
a t l o w f l a m e
position
Inner burner is
at high flame
position
Inner burner is at
low flame position
Note:
Sometimes
“
pop
”
sound
Heard when the burmer is
switch off. This is normal.
Please turn the ignition
knob clockwise to the
[OFF] position without
pressing
1 5
1 6
1 7
Cleaning top panel
A p p l y n e u t r a l
detergent on the
soft rag to clean the
s u r f a c e o f t h e
panel.
Do not use alkaline
detergent, petrol,
other corrosive
solutions or abrasive
matenals to clean
the surface of the
p a n e l , it would
p e r m a n e n t l y
damage the surface
finish to the panel.
Foam or soft rag
can clean the inner
and outer burner
caps. If the dirt is
hard to remove.it is
recommended to
use soft brush.
Do not clean it
forcefully or do not
hit it while brushing.
A f t e r c l e a n i n g ,
make sure the cap
is mounted in place.
Always keep the
burner and the
surroundings clean
to prevent trouble
of ignition.
The gas sealing
surfaces of outer
burner cap and
burner must always
be cleaned.
Otherwise it would
cause gas leakage
or fire accident.
Please use soft rag
to wipe off the dirt
on ther mocouple
surface and avoid
c r a s h t o t h e
surface.
1 8