Delta DTB4824 User Manual - User Manual

Download PDF User Manual

Full Text Searchable PDF User Manual

http://www.delta.com.tw/industrialautomation/

DELTA Temperature Controller

DTB Series

User Manual

http://www.delta.com.tw/industrialautomation/

B Series Temperature Controller

User Manual

Thank you very much for purchasing DELTA B Series. Please read this instruction sheet before using

your B series to ensure proper operation and please keep this instruction sheet handy for quick
reference.

Precaution

DANGER!

Caution! Electric Shock!

Do not touch the AC terminals while the power is supplied to the controller to prevent an electric shock.

Make sure power is disconnected while checking the unit inside.

The symbol

indicates that this Delta B Series Temperature Controller is protected throughout by DOUBLE

INSULATION or REINFORCED INSULATION (equivalent to Class II of IEC 536).

WARNING!

This controller is an open-type temperature controller. Make sure to evaluate any dangerous

application in which a serious human injury or serious property damage may occur.

Always use recommended solder-less terminals: Fork terminal with isolation (M3 screw, width is 7.0mm (6.0mm for
DTB 4824), hole diameter 3.2mm). Screw size: M3 x 6.5 (With 6.8 x 6.8 square washer). Screw size for DTB4824:
M3 x 4.5 (With 6.0 x 6.0 square washer). Recommended tightening torque: 0.4 N.m (4kgf.cm). Applicable wire:
Solid/twisted wire of 2 mm

, 12AWG to 24AWG. Please be sure to tighten them properly.

Do not allow dust or foreign objects to fall inside the controller to prevent it from malfunctioning.

Never modify or disassemble the controller.

Do not connect anything to the “No used” terminals.

Make sure all wires are connected to the correct polarity of terminals.

Do not install and/or use the controller in places subject to:

•

Dust or corrosive gases and liquid.

•

High humidity and high radiation.

•

Vibration and shock.

•

High voltage and high frequency

Must turn power off when wiring and changing a temperature sensor.

Be sure to use compensating wires that match the thermocouple types when extending or connecting the
thermocouple wires.

Please use wires with resistance when extending or connecting a platinum resistance thermometer (RTD).

10.

Please keep the wire as short as possible when wiring a platinum resistance thermometer (RTD) to the controller
and please route power wires as far as possible from load wires to prevent interference and induced noise.

11.

This controller is an open-type unit and must be placed in an enclosure away from high temperature, humidity,
dripping water, corrosive materials, airborne dust and electric shock or vibration.

12.

Please make sure power cables and signals from instruments are all installed properly before energizing the
controller, otherwise serious damage may occur.

13.

Please do not touch the terminals in the controller or try to repair the controller when power is applied to prevent an
electric shock.

14.

Wait at least one minute after power is disconnected to allow capacitors to discharge, and please do not touch any
internal circuit within this period.

15.

Do not use acid or alkaline liquids for cleaning. Please use a soft, dry cloth to clean the controller.

16.

This instrument is not furnished with a power switch or fuse. Therefore, if a fuse or power switch is required, install
the protection close to the instrument. Recommended fuse rating: Rated voltage 250 V, Rated current 1 A. Fuse

type: Time-lag fuse

17.

Note: This controller does not provide overcurrent protection. Use of this product requires that suitable overcurrent
protection device(s) must be added to ensure compliance with all relevant electrical standards and codes. (Rated
250 V, 15 Amps max). A suitable disconnecting device should be provided near the controller in the end-use
installation.

Display, LED and Pushbuttons

PV Display
SV Display

AT
OUT1/OUT2

Function key

Temperature unit LED

Down key

: to display the process value or parameter type.
: to display the set point, parameter operation read value,

manipulated variable or set value of the parameter.

: flashes

when

the

Auto-tuning

operation

ON.

: Output LED ights when the output is ON.

. Press this key to select the desired function mode and

confirm a setting value.

C, F :

ALM1 ~ ALM3 : Alarm output LED, lights when ALM1/ALM2/ALM3 is ON.
:

. Press this key to decrease values displayed on the SV

display. Hold down this key to speed up the decrements.
:

Auto-tuning LED,

, l

. Press this key to set parameters within function mode.

C : Celsius F : Fahrenheit

. Press this key to increase values displayed on the SV display.

Hold down this key to speed up the incremental action.

Mode key

key

Ordering Information

DTB

1 2 3 4 5 6

DTB Series

DTB : Delta B Series Temperature Controller

1 2 3 4

Panel Size (W×H)

4824 : 1/32 DIN W48

H24mm

4848 : 1/16 DIN W48

H48mm

4896 : 1/8 DIN W48

H96mm

9696 : 1/4 DIN W96

H96mm

1st Output Group Selection

R: Relay output, SPDT (SPST: 1/16 DIN and 1/32 DIN size), 250VAC, 5A
V: Voltage pulse output, 14V +10

﹪

~ -20

﹪

(Max. 40mA)

C: DC current output , 4 ~ 20m A
L: Linear voltage output, 0~5V, 0~10Vdc

2nd Output Group Selection

R: Relay output, SPDT (SPST: 1/16 DIN and 1/32 DIN size), 250VAC, 5A
V: Voltage pulse output, 14V +10

﹪

~ -20

﹪

(Max. 40mA)

EVENT Inputs / CT function

(Optional)

None : No EVENT input , No CT (Current transformer)
E: EVENT input is provided, No CT (Current transformer)
T: CT (Current transformer) is provided, No EVENT input
V: Valve control.

Note 1 :

DTB4824 series: no optional function provided and no extra alarm output supported, but user can set
2nd output as alarm mode.

Note 2 :

DTB4848 series: only one alarm output when optional function supported, but user can set 2nd output as
2nd alarm output.

Note 3: “Valve control” with feedback selection is only available for DTB9696RRV.

Specifications

Temperature Sensor Type and Temperature Range

Input Temperature Sensor

Type

Register Value

LED Display

Temperature Range

0~50mV Analog Input

-999 ~ 9999

4~20mA Analog Input

-999 ~ 9999

0~20mA Analog Input

-999 ~ 9999

0V~10V Analog Input

-999 ~ 9999

0V~5V Analog Input

-999 ~ 9999

Platinum Resistance (Pt100)

-200 ~ 600

Platinum Resistance (JPt100)

-20 ~ 400

Thermocouple TXK type

-200 ~ 800

Thermocouple U type

-200 ~ 500

Thermocouple L type

-200 ~ 850

Thermocouple B type

100 ~ 1800

Thermocouple S type

0 ~ 1700

Thermocouple R type

0 ~ 1700

Thermocouple N type

-200 ~ 1300

Input Voltage

100 to 240VAC 50/60Hz

Operation Voltage
Range

85% to 110% of rated voltage

Power Consumption

5VA max.

Memory Protection

EEPROM 4K bit (non-volatile memory (number of writes: 100,000)

Display Method

2 line x 4 character 7-segment LED display Process value(PV): Red color, Set point(SV):
Green color
Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK
3-wire Platinum RTD: Pt100, JPt100

Sensor Type

Analog input: 0~5V, 0~10V, 0~ 20 m A, 4~20 m A, 0~50mV

Control Mode

PID, ON/OFF, Manual or PID program control (Ramp/Soak control)
Relay output: SPDT (SPST: 1/16 DIN and 1/32 DIN size), Max. load 250VAC, 5A resistive load
Voltage pulse output: DC 14V, Max. output current 40mA
Current output: DC 4 ~ 20m A output (Load resistance: Max. 600

)

Control Output

Linear voltage output: 0~5V, 0~10V

Display Accuracy

0 or 1 digit to the right of the decimal point (selectable)

Sampling Rate

Analog input: 150 msec/ per scan Thermocouple or Platinum RTD: 400 msec/per scan

RS-485 Communication MODBUS ASCII / RTU communication protocol
Vibration Resistance

10 to 55Hz, 10m/s

for 10min, each in X, Y and Z directions

Shock Resistance

Max. 300m/ s

, 3 times in each 3 axes, 6 directions

Ambient Temperature

C to +50

Storage Temperature

-20

C to +65

Altitude

2000m or less

Relative Humidity

35% to 80% (non-condensing)

Thermocouple E type

0 ~ 600

Thermocouple T type

-200 ~ 400

Thermocouple J type

-100 ~ 1200

Thermocouple K type

-200 ~ 1300

Note 1 : An external 250

precision resistor should be connected when the current input is selected as the input

temperature sensor type..

Note 2 :

(Operation mode) must be set if user wish to specify decimal point position. Except for the

thermocouple B, S, R type, the decimal point positions of all the other thermocouple type input sensors can
be set.

The default range of analog input is -999 ~ 9999. For example, when a 0~20mA analog input is selected as the

input temperature sensor type, -999 indicates 0mA and 9999 indicates 20mA. If change the input range to 0 ~
2000, then 0 indicates 0mA and 2000 indicates 20mA. One display scale is equal to 0.01mA.

Operation

There are three modes of operation: operation, regulation and initial setting. When power is applied, controller
gets into the operation mode. Press the

key to switch to regulation mode. If the

key is pressed for

more than 3 seconds, controller will switch to the initial setting mode. Pressing the

key while in the

regulation mode or initial setting mode, forces the controller to return to the operation mode.
PV/SV: Sets the temperature set point and displays the temperature process value. Use

keys to set the

temperature set point.

Setting method: While in any function mode, press the

key to select the desired function and use the

keys to change settings. Press

key to save the changes.

The next flow chart shows how to switch for settings and internal functions:

Regulation Mode

Operation Mode

Initial Setting Mode

Press key less than 3 sec

Press key

Press key more than 3 sec

Press key

Regulation Mode

Operation Mode

Initial Setting Mode

Auto-tuning

(Set in PID control and RUN mode)

Press

Use key to

set temperature set point

Press

Set input type

Press

4 groups PID modes (n=0~3). When n=4,
PID control is auto regulated.

Press

Control setting RUN or STOP

Set temperature unit

do not display when analog input

Press

PD control offset

setting

(When PID control is ON and Ti=0,
set the value of PdoF.

Press

Start pattern setting (PID

program control and

Time setting.

Press

Set upper-limit of
temperature range

Press

Heating hystereisis setting

(Set in ON/OFF control mode)

Press

Decimal point position selection

(except for B, S, R type, all the
other types can be set)

Press

Set lower-limit of

temperature range

Press

Cooling hystereisis setting

(Set in ON/OFF control mode)

Press

Upper-limit alarm 1

(This parameter is available only when
ALA1 function enables)

Press

Select control mode

(See "Pattern and set Editing
selection" for detail)

Press

Heating/Cooling

control cycle setting

(Set in PID control mode)
Press

Lower-limit alarm 1

(This parameter is available only when
ALA1 function enables)

Press

Select heating/cooling control
or dual loop output control

Press

Control cycle setting

of 2nd output group

(Set in PID control and Dual Loop

output control mode)

Press

Upper-limit alarm 2

(This parameter is available only when
ALA2 function enables)

Press

Alarm 1 mode setting

Press

P value of 2nd output group =

(P value of 1st output group)

P value of 1st & 2nd output group
during dual loop output control

Press

Lower-limit alarm 2

(This parameter is available only when
ALA2 function enables)

Press

Alarm 2 mode setting

Press

Dead Band (Set in Dual Loop

output control mode)

Upper-limit alarm 3

(This parameter is available only when
ALA3 function enables)

Press

Alarm 3 mode setting

Press

Switch setting for feedback

signal of valve. (Display when
valve control is ON)

Lower-limit alarm 3

(This parameter is available only when
ALA3 function enables)

Press

Set system alarm

Press

Automatically regulate

feedback value.

Press

(Display when valve control is ON)

Setting lock mode

Press

Communication write function
enable/disable

Press

Time setting for valve from

full close to full open. (Display when

valve control is ON)

Press

Display and adjust output value
of 1st output group

(Display in PID control mode and manual

RUN mode)

Press

ASCII, RTU communication
format selection

Press

Valve Dead Band setting.

Press

(Display when valve control is ON)

Display and adjust output value
of 2nd output group

(Display in dual loop PID control mode and
manual RUN mode)

Press

Communication address
setting

Press

Upper-limit regulation of

valve output with feedback to

controller. (Display when valve

signal feedback function is ON)

Press

In case of using an external CT,
the controller displays the current
value being measured by CT, if
the control output is ON

Press

to return to set target temperature

Communication baud
rate setting

Press

Lower-limit regulation of

valve output with feedback to

controller. (Display when valve

signal feedback function is ON)

Press

Valve output with feedback.

(Display when valve feedback

function is ON)

Press

Data length setting

Press

Regulate temperature

deviation value

DA value feedback of valve.

(Display when valve feedback

function is ON)

Press

Back to target temperature

Parity bit setting

Press

(The setting display when analog output)
Press

Regulate upper-limit of analog

output value

Stop bit setting

Press to return input type setting

Press

Regulate lower-limit of analog
output value

(The setting display when analog output)

to return to auto-tuning mode

※

1 Scale = 2.8uA = 1.3mV for tuning output value

PID mode selection: any one of 4 groups PID modes (n=0~3) can be selected. When n=4, program will

automatically select 1 group PID that is most useful for target temperature.

Select n=0~4 to

decide PID mode.

0~3 groups PID

Press

PID setting: n=0.Press

PID setting: n=3.Press

Proportion band setting: n=0.

Press

Proportion band setting: n=3.

Press

Ti setting: n=0. Press

Ti setting: n=3. Press

Td setting: n=0.Press

Td setting: n=3.Press

Integral deviation setting: n=0.

AT setting.

Press

back to PID deviation setting

Integral deviation setting: n=3.
AT setting.

Press

back to PID deviation setting

Pattern and step editing selection: edit

parameter. The following display is the example operation of pattern

No. 0.

select OFF

Press

Select desired editing pattern
number

select number

Edit temperature of step No. 0
of pattern No. 0

Press

Select actual step No. when
program control is executing

Press

Exit p

attern and step editing selection

Switch to and continue setting

Edit time of step No. 0 of
pattern No. 0, unit is hh.mm

Press

Set additional execution cycle

number(0 to 99)

Press

Set step No. 07 in order

Press

Edit temperature of step No. 7

of pattern No. 0

Set link pattern, OFF indicates

the program end

Press to return pattern No. editing
mode

Press to set actual step No.

Edit time of step No. 7 of
pattern No. 0, unit is hh.mm

Dual Loop Output Control (Heating / Cooling Control)

OFF

Set point

Heating

Dead band

Heating hysteresis

Figure 1. Output

during dual loop output control

operation of ON/OFF control

Cooling hysteresis

Cooling

Temperature control can be achieved either by heating or cooling. In DTB
series, heating and cooling can be operated simultaneously (Dual Loop
output control) to perform temperature control. When Dual Loop output
control are used, two control outputs must be connected to the heating and
cooling devices. Please refer to the following for the operation:

: This parameter is used to select heating or cooling action if

operate either heating or cooling function in this controller. When selecting

, 1st output group is heating (reverse) control, and when selecting
, 1st output group is cooling (forward) control. At this moment, 2nd

output group is regarded as an alarm output. If user select

it indicates that user can operate Dual Loop output control function in this
controller. When selecting

, 1st output group is heating (reverse)

control and 2nd output group is cooling (forward) control. When selecting

, 1st output group is cooling (forward) control and 2nd output group is

heating (reverse) control.

Output

Dead band: dead
band width=positive

Set point

Heating

Cooling

Figure 2. PID

Dead Band is positive

control,

In DTB series, P (Proportional Band), I(Integral Time) and D(Derivative
Time) parameters are automatically set by using the Auto-tuning (AT)
function.

: This parameter is for the control mode that must be Dual Loop

output control with PID control method configured. The value of P, I and D of
1st output group can be set immediately. The P value of 2nd output group is
equal to (P value of 1st output group) x

and the value of I and D of

2nd output group are the same as the value of I and D of 1st output group.

: Dead Band, shown as the following figure 1, 2 and 3. This

parameter sets an area in which the heating and cooling control output is 0
centering around the set point in a Dual Loop output control mode.

Settings lock.

To avoid incorrect operation, two key lock functions

are provided.

: Lock 1 can lock all settings. All parameters and

temperature settings can be locked to disable changes.

: Lock 2

can lock settings except the SV (Set point) value. All parameters and
temperature settings can be locked with the exception of the SV value.

Press

and

key simultaneously, the “Lock” status can be

released.

Output

Dead band: dead
band width=negative

Set point

Heating

Cooling

Figure 3. PID

Dead Band is negative

control,

Alarm

Outputs

There are up to three groups of alarm outputs and each group allows thirteen alarm types in the initial setting
mode. The alarm output is activated whenever the process temperature value (PV) is getting higher or lower than
the set point of alarm limit.

Set

Value

Alarm Type

Alarm Output Operation

Alarm function disabled

Output is OFF

Deviation upper- and lower-limit:
This alarm output operates when PV value is higher than the setting value
SV+(AL-H) or lower than the setting value SV-(AL-L).

OFF

SV-(AL-L)

SV+(AL-H)

2 Deviation

upper-limit:

This alarm output operates when PV value is higher than the setting value
SV+(AL-H).

OFF

SV+(AL-H)

3 Deviation

lower-limit:

This alarm output operates when PV value is lower than the setting value SV-(AL-L).

OFF

SV-(AL-L)

Reverse deviation upper- and lower-limit:
This alarm output operates when PV value is in the range of the setting value
SV+(AL-H) and the setting value SV-(AL-L).

OFF

SV-(AL-L)

SV+(AL-H)

Absolute value upper- and lower-limit:
This alarm output operates when PV value is higher than the setting value AL-H or
lower than the setting value AL-L.

OFF

AL-L

AL-H

Absolute value upper-limit:
This alarm output operates when PV value is higher than the setting value AL-H.

OFF

AL-H

Absolute value lower-limit:
This alarm output operates when PV value is lower than the setting value AL-L.

OFF

AL-L

Deviation upper- and lower-limit with standby sequence:
This alarm output operates when PV value reaches set point (SV value) and the
value is higher than the setting value SV+(AL-H) or lower than the setting value
SV-(AL-L).

OFF

SV-(AL-L)

SV+(AL-H)

Deviation upper-limit with standby sequence:
This alarm output operates when PV value reaches set point (SV value) and the
reached value is higher than the setting value SV+(AL-H).

SV+(AL-H)

OFF

10 Deviation lower-limit with standby sequence:

This alarm output operates when PV value reaches the set point (SV value) and the
reached value is lower than the setting value SV-(AL-L).

SV-(AL-L)

OFF

11 Hysteresis upper-limit alarm output:

This alarm output operates if PV value is higher than the setting value SV+(AL-H).
This alarm output is OFF when PV value is lower than the setting value SV+(AL-L).

OFF

AL-L AL-H

12 Hysteresis lower-limit alarm output:

This alarm output operates if PV value is lower than the setting value SV-(AL-H).
This alarm output is OFF when PV value is higher than the setting value SV-(AL-L).

OFF

AL-H AL-L

13 CT alarm output:

This alarm operates when the current measured by transformer (CT) is lower than
AL-L or higher than AL-H (This alarm output is available only for the controller with
current transformer).

OFF

AL-L

AL-H

14 When program control is end status, alarm output is ON.

15 When RAMP UP status happens to PID program control, alarm output is ON.

16 When RAMP DOWN status happens to PID program control, alarm output is ON.

17 When SOAK status happens to PID program control, alarm output is ON.

18 When RUN status happens to PID program control, alarm output is ON.

Note: AL-H and AL-L include AL1H, AL2H, AL3H and AL1L, AL2L, AL3L

Current Transformer (CT) Function

The Current Transformer (CT) function is used with the alarm output. When using a current transformer (CT) with

the controller, change the corresponding alarm output mode to mode 13 (alarm output set value is 13), then turn

to operation mode and set the current lower-limit and current upper-limit. You can set current alarm range

between 0.5A ~ 30A, display resolution is 0.1A and measure accuracy is +/- 0.5A.

EVENT Inputs Function

There are two optional event inputs (contact inputs) supported (EVENT1and EVENT2) in DTB series.

EVENT1:

RUN/STOP operation can be executed by RUN/STOP parameters (Operation Mode) or via the

communication. User also can control RUN/STOP operation by EVENT 1 in DTB series. The control

output is ON if the circuit of EVENT 1 is open when the controller is operating. Otherwise, the

controller will stop output if the circuit of EVENT 1 is short or when the system parameter of the

controller is set to STOP mode.

EVENT2:

DTB series allows user can switch two temperature setting value by changing the status (open/short) of

EVENT 2. Each temperature setting value has independent control parameters.

PID Program Control (Ramp/Soak Program Control)

Description of Function and Parameters Setting:

PID program control by 8 patterns (Pattern No. 0~7) is supported in DTB series. Each pattern contains 8 steps

(step No. 0 ~ 7), one Link Pattern parameter, one Cycle parameter and one Actual Step parameter.

Start Pattern

is in operation mode and it is used to set the Start Pattern of PID program control (This

parameter appear in

mode only).

Steps :

Include set point X and execution time T, these two parameters setting. The set point (SV) should reach

temperature X after the period of execution time T. If the set point is the same as the result of the previous
setting, then it is called Soak program control. If not, then it is called Ramp program control. Therefore,
PID program control is also called Ramp/Soak program control. The default of step No. 0 in this controller
is Soak program control. The controller will control the temperature (PV) to reach the set point X and then
keep the temperature at set point X. The period of execution time is time T which provided by step No. 0.

Link Pattern Parameter :

For example, when set

to 2, it indicates that pattern No. 2 will execute next after

the execution of pattern No. 0. If set to

, it indicates the program will stop after executing the current

pattern and the temperature will keep at the set point of the last step.

Cycle Parameter :

Additional execution cycle number. For example, when set

to 2, it indicates that pattern

No. 4 should execute twice in addition. Include origin one time execution, total execute three times.

Actual Step Parameter :

Execution step number per pattern (can set to 0 ~ 7). For example, when set

2, it indicates that pattern No 7 will not execute other steps than step 0 to step2.

Execution :

When

is set to

, the program will start to execute in order from the step 0 of start

pattern. When

is set to

, the program will stop and the control output is disabled. When

is set to

, the program will stop and the temperature at that time will be controlled at the set

point before program stop. Select

again, then the program will restart and execute from step 0 of

start pattern. When

is set to

, the program will hold and the temperature at that time will be

controlled at the set point before program hold. Select

again, then the program will follow the step

before hold and start to execute through the rest of the time.

Display :

During PID program control, the SV default display is P-XX, P indicates the current execution pattern

and XX indicates the current execution step. Press

to change the display item. After select

press

key, and then the temperature set point of the current execution step will display on SV

display.After select

, press

key, and then the residual time of the current execution step will

display on SV display.

PID Control

One group can be selected from any one of 4 groups PID parameters (P, I, D, IOF) for PID control. After AT, PID

value and temperature setting will be stored in the selected one group.

PIDn, n=0~4 from which

0~3 correspond to each PID parameter.

: n=4, auto PID parameter. Program will automatically select a most

useful PID parameter based on current temperature setting. Displayed SV values correspond to

Temperature setting corresponded to the selected PID parameter via user-defined or AT.

Valve Control:

When use valve control as output control, there are 2 Relay outputs for motor forward/reverse control, one (output

1) for valve open the other (output 2) for valve close. The output volume is controlled by valve open/close and it
can be set with feedback function enabled or disabled. When feedback is disabled, output 1 will keep output while
valve fully opens and output 2 will keep output while valve fully closes. But if feedback is enabled, please follow the
parameter setting for valve control as follows:

: Time for valve from full close to full open.
: Dead Band setting of valve. The value of current valve output minus previous one must be greater than

Dead Band value; otherwise, valve will remain OFF.

: Signal feedback setting, ON for enabling feedback and OFF for disabling feedback.

When

set to ” 1”, it means signal feedback function is activated and will come up selections as follows:

: Upper/Lower limit of valve feedback by auto-tuning.

must set to

for showing up this

selection.

: D/A value when value fully opens. Set

to be ”1” for auto setting or ”0” for manual setting.

: D/A value when value fully closes. Set

to be ”1” for auto setting or “0” for manual setting.

Note: If feedback function setting is with problem, program will see the setting as feedback disabled.

RS-485 Communication

1. Supporting transmission speed: 2400, 4800, 9600, 19200, 38400bps
2.  Non-supported formats: 7, N, 1 or 8, O, 2 or 8, E, 2
3.  Communication protocol: Modbus (ASCII or RTU)
4.  Function code: 03H to read the contents of register (Max. 8 words). 06H to write 1 (one) word into register.

02H to read the bits data (Max. 16 bits). 05H to write 1 (one) bit into register.

5. Address and Content of Data Register:

Address Content

Explanation

Measuring unit is 0.1, updated one time in 0.4 second
The following reading value display indicates error occurs:
8002H : Initial process (Temperature value is not got yet)
8003H : Temperature sensor is not connected

1000H Process value (PV)

8004H : Temperature sensor input error

8006H : Cannot get temperature value, ADC input error

1000H

Process value (PV)

8007H : Memory read/write error

1001H Set point (SV)

Unit is 0.1,

C or

1002H Upper-limit of temperature

range

The data content should not be higher than the temperature range

1003H Lower-limit of temperature

range

The data content should not be lower than the temperature range

1004H

Input temperature sensor type

Please refer to the contents of the “Temperature Sensor Type and
Temperature Range” for detail

1005H Control method

0: PID, 1: ON/OFF, 2: manual tuning, 3: PID grogram control

1006H Heating/Cooling control

selection

0: Heating, 1: Cooling, 2: Heating/Cooling, 3: Cooling/Heating

1007H 1st group of Heating/Cooling

control cycle

0~99, 0:0.5 sec

1008H 2nd group of Heating/Cooling

control cycle

0~99, 0:0.5 sec

1009H PB Proportional band

0.1 ~ 999.9

100AH Ti Integral time

0~9999

100BH Td Derivative time

0~9999

100CH Integration default

0~100%, unit is 0.1%

100DH Proportional control offset

error value, when Ti = 0

0~100%, unit is 0.1%

100EH The setting of COEF when

Dual Loop output control are
used

0.01 ~ 99.99

100FH The setting of Dead band

when Dual Loop output control
are used

-999 ~ 9999

1010H Hysteresis setting value of the

1st output group

0 ~ 9999

1011H Hysteresis setting value of the

2nd output group

0 ~ 9999

1012H Output value read and write of

Output 1

Unit is 0.1%, write operation is valid under manual tuning mode only.

1013H Output value read and write of

Output 2

Unit is 0.1%, write operation is valid under manual tuning mode only.

1014H Upper-limit regulation of

analog linear output

1 Unit = 2.8uA(Current Output) = 1.3mV(Linear Voltage Output)

1015H Lower-limit regulation of

analog linear output

1 Unit = 2.8uA(Current Output) = 1.3mV(Linear Voltage Output)

1016H Temperature regulation value -999~+999, unit: 0.1
1017H Analog decimal setting

0 ~ 3

1018H Time for valve from full open

to full close

0.1~999.9

1019H Dead Band setting of valve

0~100%; unit: 0.1%

101AH Upper-limit of feedback

signal set by valve

0~1024

101BH Lower-limit of feedback

signal set by valve

0~1024

101CH PID parameter selection

0~4

101DH SV value corresponded to

PID value

Only valid within available range, unit: 0.1 scale

1020H Alarm 1 type