Full Text Searchable PDF User Manual
GSM/GPRS/GPS
TK309 GPS Tracker User Manual
Preface
Thank you for purchasing the tracker. This manual shows how to operate the
device smoothly and correctly. Make sure to read this manual carefully
before using this product. Please note that specification and information are
subject to changes without prior notice in this manual.
Any change will be integrated in the latest release. The manufacturer assumes
no responsibility for any errors or omissions in this document.
◆
Quick using
1
)
Open device case, proper insert GSM card, connect external power
supply,
Must turn on small switch inside SIM card hole.
2
)
Put device outside, around 30s three lights will keep lighting on stands
for device can work normally.
3
)
Dialing device number, it will hang up and reply tracking message with
valid Longitude and latitude.
4
)
If need track online system, send 2 SMS connects to platform as
below:
SMS1:#IP#123456#220.231.203.248#7700#
SMS2: #apn#123456#APN of operator#APN user name#APN password#
5
)
Login platform to track in real time(please contact supplier).
1.
Specifications
Content
Specs.
Dim.
73mm x 33mm x 13mm
Weight
35g
Network
GSM/GPRS/GPS
Band
850/900/1800/1900 Mhz
GPS chip
U-blox7
GSM module
MTK6261D
GPS sensitivity
-159dBm
GPS accuracy
5m
Time To First Fix
Cold status 45s
Warm status 35s
Hot status 1s
Work voltage
9V-80V
Storage Temp.
-40°C to +85°C
Operation Temp.
-20°C to +55°C
Humidity
5%--95%
◆
Installation attentions
NOTE: device front side towards the sky.
When install in car, if the windscreen glued by metal thermal insulation
layer or heating layer, it will reduce the GPS receive signal and lead to
GPS work disorder.
Device light description
Light
Represents
yellow
GSM signal normal
blue
GPS signal normal
Red
Power
1.Installation instructions
1.1 Preparation
1.1.1 Open the package to check the device model number is correct, be
with full accessories, or else please contact your supplier;
Choose SIM card, need insert a GSM SIM card into the device, please
refer to the suggestion of your supplier for SIM card choice.
Notice:
Please insert SIM card before turning the device power switch to on
;
The SIM card need open the GPRS function;
Please make sure SIM card with full balance.
2.Device wiring requirements
◆
Attentions
◆
Device light
1
)
No yellow light: failed to read SIM card, need reinstall SIM card. 2
)
Blue
light flash: no GPS signal, make sure device started outside. 3
)
Three lights off:
lights entered sleep mode, make a call or move device can wake up.
◆
Device failed located
1
)
Failed located: message replied with all 0, make sure device started outside
not in room.
2
)
Can’t reach the call: make sure SIM card has balance and installed
Properly and opened the switch.
◆
Device can’t track on platform
1) Check three lights are stable on.
2) Make sure device can work and reply valid tracking long&Lat in SMS.
3) Send SMS
#check#123456# , it will reply you device setting
status to check IP,Port,APN etc.
3.User Settings
1.Initialization (initialize the settings)
Text command
Parameter
Example
Command
#super#
#super#
Command Feedback
super ok
2.Single Locating : Two ways
1.Dialing tracking
make a call to device number, it will hang up and reply a real-time tracking
message.
2.SMS tracking
Send SMS command,it will reply your location.
Text command
Parameter
Example
Command
#smslink#password#
#smslink#123456#
Command Feedback
Google link + Speed + Time + Date + IMEI
3.Authorized number (All alarm messages will be sent to authorized number only)
Text command
Parameter
Example
Add Authorized number #admin#123456#phone number#
#admin#123456#18575518750#
Command Feedback
admin ok
Del Authorized number #noadmin#123456#phone number#
#noadmin#123456#13409877890#
Command Feedback
noadmin ok
(
If notified not admin number,send #super# please
)
4.Set password
Text command
Parameter
Example
Command
#password#old
password#new
passwod#
#password#123456#666888#
Command Feedback
Password ok
5.Set data to upload interval
Text command
Parameter
Example
Command
#at#123456#10~600#
#at#123456#10#
Command Feedback
at ok
Command description
The data upload interval can be set as you need, 10~600 represents seconds
of data uploading interval, default as 10 seconds for real time tracking.
6.Device reboot
Text command
Parameter
Example
Command
#reboot#password#
#reboot#123456#
Command Feedback
reboot ok
Command description
The device will restart within 30 seconds
7.Set all alarm mode
Text command
Parameter
Description
Command
#KC#123456#0#
To close alarm function
Command
#KC#123456#1#
Alarm will reply only SMS
Command
#KC#123456#2#
Alarm will reply only call back
Command
#KC#123456#3#
Alarm will reply via SMS and call
8.Timezone Setting
Text command
Parameter
Example
Command
#timezone#password#direction#time
zone value in hours#time zone in
minutes#
In UTC-6 example:
#timezone#123456#W#6#00#
In UTC+5.30
#timezone#123456#E#5#30#
Command Feedback
timezone ok
9.Check vehicle state
Text command
Parameter
Example
Command
#check#password#
#check#123456#
Command Feedback
IMEI + Authorized number +Alarm mode + IP + GPS status + Data upload interval
status + APN + Time zone + ACC status
10.Geo-fence
Text command
Parameter
Example
Command
#stockade#password#meter#
#stockade#123456#300#
Command Feedback
stockade ok
Command description
send SMS: “#stockade#123456#300#”, “300” represents 300 meters.In
case of breach, it will send SMS “stockade alarm + IMEI + Coordinates” to
the authorized number.
11.Overspeed alarm
Text command
Parameter
Example
Command
#speed#password#speed number in
3 digits#
#speed#123456#060#
Command Feedback
speed ok
Command description
Sample means When the car moves exceeding 60 km/h, the unit will send
SMS alert “speed alarm +imei+ Coordinates ” to the authorized number.
12.Vibration alarm
Text command
Parameter
Description
Command
#vibrate#123456#1#
1 means
Slight vibration level
Command
#vibrate#123456#2#
2 means m
edium vibration level
Command
#vibrate#123456#3#
3 means h
igh sensitive level
Command description
When the tracker detect the vibration,it will send “vibrate alarm + IMEI
+Google map link” to authorized phone number.
13.Cut oil or
electricity (Optional with relay)
Text command
Parameter
Example
Command
#stopoil#password#
#stopoil#123456#
Command Feedback
stop oil ok
Command
#supplyoil#123456#
#supplyoil#123456#
Command Feedback
supply oil ok
14.ACC alarm
Text command
Parameter
Sample
Command
#ACC#Password#1#
#ACC#123456#1#
Command Feedback
acc alarm on
Command
#ACC#Password#0#
#ACC#123456#0#
Command Feedback
acc alarm off
Command description
When the device detects the voltage input,it will reply “ACC
Alarm+IEMI+Coordinates ” to authorized number
15.Power failure alarm
Description
If device was removed from car battery, device will end SMS “cut power
alert! +IMEI number+Long&Lat” to the authorized number.
Web based platform
www.gpstky.net
further details please contact
manufacturer.
1.Setting APN
1.1 APN standards for Access Point Name and differs from country to country.
For more information about the local APN, inquiry from your local GPRS
network operator.
1.2 Send SMS “
#apn#password#APN content#APN user name#APN
password#
” via a cell phone and if succeeded, the tracker will return the
message “set APN OK”.
E.g. send SMS command “#apn#123456#cmnet#”.
Notes: CMNET is the APN content of China Mobile (it has no APN user name
and password).
2.IP and Port setting
Send SMS “
#IP#password#ip address#port number#
”. If succeeded,
“set ip address and port ok” will be returned by SMS.
E.g, Send SMS command “#IP# password #220.231.203.248#7700#” to the
device (220.231.203.248 is IP,7700 is port, IP is in capital)
4.Cautions
Please comply with the instructions to extend the unit life:
1. Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the
inside circuitry.
2. Don’t use & store the unit in dusty places.
3. Don’t put the unit in overheated or overcooled places.
4. Handle carefully. Don’t vibrate or shake it violently.
5. Clear the unit with a piece of dry cloth. Don’t clean in chemicals, detergent.
6. Don’t paint the unit, this may cause some foreign materials left in between the
parts.
7. Don’t disassemble or refit the unit.
8. Please read the user manual carefully before installation and operation, learn
something more about the voltage range. Otherwise, it won’t work properly or
destroy the product.